Skip to main content
Skip to main content
Product title:

2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack)

Product rating:
Product price:
$179.99
Product SKU ! 701 CCW-GA (2 Pack)
Product MPN ! PU-047040
Product availability: In Stock
Bullet point features

Frequently Bought Together

Total Price: $199.98

Description

Englander Auger Motor Replacements / Includes BOTH Upper & Lower Motors

Part Number: AMP20131-GA

More Info:

This auger motor is designed to fit Englander pellet stoves including models 25-PDV and 25-PDVC (two per unit) and is the stirrer motor on Englander's 10-CPM multi-fuel stove. Our Englander auger motor comes fully assembled, is simple to install and has built-in leads that connect to your existing stove's wiring. The auger motor mounts securely to the auger shaft and will have your stove up and running in minutes. This auger motor is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel. Our Englander replacement auger motor will have your auger system running smoothly while keeping you warm during the cold winter months.

Instructions for replacing the Auger Motors

To replace the Top Auger, all the fuel must be removed from the hopper as well as from the Top Auger assembly. Once this is done, the four bolts that hold in the bearing can be removed, followed by the complete auger assembly. Loosen the two (2) set screws with a 1/8” Allen wrench, which will disconnect the bearing from the shaft (the bearing assembly and auger assembly can be replaced by reversing this procedure). When placing the auger assemblies in the unit, always tighten the four bolts in a diagonal pattern to ensure the bearings and shafts are aligned properly. NOTE: Follow the same procedure to work on the bottom auger, with the exception that the pellets do not have to be removed from the hopper.


Replacement For Part Numbers:

  • PU-047040
  • 44269

View Compatible Models

UPC: 794909901109

Compatible Models

    Englander

  • 10-CPM
  • 25-CAB80
  • 25-PAF
  • 25-PDV
  • 25-PDVC
  • 25-PDVE, 55-SHP22E
  • 25-PDVP
  • 25-PFS
  • 25-PI

Technical Specs

RPM 1
Direction Counter Clockwise
Volts 120
Amps .72
Shaft 5/16"
Connector Male Spades

Videos

Instructions

Install Instructions For 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack)

Unplug stove and remove the rear service panel. Locate the auger motors and remove the wire terminals from each motor. Stoves that were made prior to 2004 will have wires permanently attached to the motor and will need to be unplugged at the control panel. Each auger motor is held in place by a 5/16" (8mm) square set screw. Simply loosen this screw and the auger motor will slide out. Align the new motor so that the set screw is on the flat side of the auger motor shaft and tighten the motor in place.

Troubleshooting

Units built from 2004 to present have a diagnostic test mode built into the circuit board. This can be used to test the individual electrical components of the unit.

WARNING: This mode can not be used to operate the stove! Attempting to burn this unit in this mode can cause damage to the unit.

Note: The stove should be completely empty of fuel and cold when using the diagnostic mode for testing the unit.

1) Unplug the stove. Locate the low burn air and air on temp buttons at the bottom of the touch pad. To start diagnostic, plug in the stove and then quickly push these buttons at the same time, then release. A number code will appear in the digital readout, this is the reading for the heat sensor. The blower speed number may change some while displayed. This is normal.

2) At this point press the low burn air button  located at the bottom center of the touchpad. After pushing, a dash appears in the blower speed window.

3) Press the blower speed up arrow , and release, the exhaust blower will come on and you should see a circle in the blower speed and a dash then appears in the heat range.

4) Next, press the blower speed down arrow , this will turn on the room air blower and you will see in the display an 8 in the blower speed and the dash in the heat range

5) Press the heat range down arrow this will turn on the lower auger motor, you will see a circle in the heat range and an 8 in the blower speed.


6) Press the heat range up arrow next, this will start the auger motor, you will see an 8 in both displays at this time.

7) The low burn air button at the bottom center of the control board will turn on the auto igniter element, and the red light above the button will light up when pressed, look through the glass in the front door and watch for 2 to 3 minutes for the igniter to start to glow.


8) To turn off any of these components simply push again the same button that turned it on . To take the unit out of diagnostic mode, unplug the unit and plug it back in, this will reset the control board back into its "run mode".







Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Information

This Item Qualifies For Free Shipping With Orders Over $199!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information
Jump back to product information tab navigation

Description

Englander Auger Motor Replacements / Includes BOTH Upper & Lower Motors

Part Number: AMP20131-GA

More Info:

This auger motor is designed to fit Englander pellet stoves including models 25-PDV and 25-PDVC (two per unit) and is the stirrer motor on Englander's 10-CPM multi-fuel stove. Our Englander auger motor comes fully assembled, is simple to install and has built-in leads that connect to your existing stove's wiring. The auger motor mounts securely to the auger shaft and will have your stove up and running in minutes. This auger motor is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel. Our Englander replacement auger motor will have your auger system running smoothly while keeping you warm during the cold winter months.

Instructions for replacing the Auger Motors

To replace the Top Auger, all the fuel must be removed from the hopper as well as from the Top Auger assembly. Once this is done, the four bolts that hold in the bearing can be removed, followed by the complete auger assembly. Loosen the two (2) set screws with a 1/8” Allen wrench, which will disconnect the bearing from the shaft (the bearing assembly and auger assembly can be replaced by reversing this procedure). When placing the auger assemblies in the unit, always tighten the four bolts in a diagonal pattern to ensure the bearings and shafts are aligned properly. NOTE: Follow the same procedure to work on the bottom auger, with the exception that the pellets do not have to be removed from the hopper.


Replacement For Part Numbers:

  • PU-047040
  • 44269

View Compatible Models

UPC: 794909901109

Technical Specs

RPM 1
Direction Counter Clockwise
Volts 120
Amps .72
Shaft 5/16"
Connector Male Spades

Video

Instructions

Assembly Instructions For 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack)

Unplug stove and remove the rear service panel. Locate the auger motors and remove the wire terminals from each motor. Stoves that were made prior to 2004 will have wires permanently attached to the motor and will need to be unplugged at the control panel. Each auger motor is held in place by a 5/16" (8mm) square set screw. Simply loosen this screw and the auger motor will slide out. Align the new motor so that the set screw is on the flat side of the auger motor shaft and tighten the motor in place.

Troubleshooting

Units built from 2004 to present have a diagnostic test mode built into the circuit board. This can be used to test the individual electrical components of the unit.

WARNING: This mode can not be used to operate the stove! Attempting to burn this unit in this mode can cause damage to the unit.

Note: The stove should be completely empty of fuel and cold when using the diagnostic mode for testing the unit.

1) Unplug the stove. Locate the low burn air and air on temp buttons at the bottom of the touch pad. To start diagnostic, plug in the stove and then quickly push these buttons at the same time, then release. A number code will appear in the digital readout, this is the reading for the heat sensor. The blower speed number may change some while displayed. This is normal.

2) At this point press the low burn air button  located at the bottom center of the touchpad. After pushing, a dash appears in the blower speed window.

3) Press the blower speed up arrow , and release, the exhaust blower will come on and you should see a circle in the blower speed and a dash then appears in the heat range.

4) Next, press the blower speed down arrow , this will turn on the room air blower and you will see in the display an 8 in the blower speed and the dash in the heat range

5) Press the heat range down arrow this will turn on the lower auger motor, you will see a circle in the heat range and an 8 in the blower speed.


6) Press the heat range up arrow next, this will start the auger motor, you will see an 8 in both displays at this time.

7) The low burn air button at the bottom center of the control board will turn on the auto igniter element, and the red light above the button will light up when pressed, look through the glass in the front door and watch for 2 to 3 minutes for the igniter to start to glow.


8) To turn off any of these components simply push again the same button that turned it on . To take the unit out of diagnostic mode, unplug the unit and plug it back in, this will reset the control board back into its "run mode".







Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping With Orders Over $199!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information

Customer Reviews

Based on 10 reviews
90%
(9)
10%
(1)
0%
(0)
0%
(0)
0%
(0)
G
Gerald V.

Very satisfied with this service. .

E
Elizabeth R.
This store had the right parts to make my stove like new

Thank you for awsome sales associate who recommended the right parts for my stove it runs like new

J
Jodi
Parts were correct and worked

Thank you to customer service for helping me get the right parts

T
Ted H.
Reliable heat again

Ordered a new control board from Stove & Grill Parts for Less as I had replaced augers and still could not keep the Englander pellet stove running for more than 5 minutes. My order was delivered very quickly (within a week), instructions were clear and easy to understand, and within 15 minutes the stove was working like new. Great service and turn-around from Stove & Grill Parts for Less and as the temps drop below freezing I’ve got heat!

E
Edward D.

2 Pack Of Englander Auger Motors By Gleason Avery, PU-047040-AMP-GA (2 Pack)

QUESTIONS & ANSWERS

If your question does not concern this specific product, use our contact form

Have a Question?

Be the first to ask a question about this.

Ask a Question

Customer Reviews

Based on 10 reviews
90%
(9)
10%
(1)
0%
(0)
0%
(0)
0%
(0)
G
Gerald V.

Very satisfied with this service. .

E
Elizabeth R.
This store had the right parts to make my stove like new

Thank you for awsome sales associate who recommended the right parts for my stove it runs like new

J
Jodi
Parts were correct and worked

Thank you to customer service for helping me get the right parts

T
Ted H.
Reliable heat again

Ordered a new control board from Stove & Grill Parts for Less as I had replaced augers and still could not keep the Englander pellet stove running for more than 5 minutes. My order was delivered very quickly (within a week), instructions were clear and easy to understand, and within 15 minutes the stove was working like new. Great service and turn-around from Stove & Grill Parts for Less and as the temps drop below freezing I’ve got heat!

E
Edward D.

2 Pack Of Englander Auger Motors By Gleason Avery, PU-047040-AMP-GA (2 Pack)