Harman Igniter Cradle Cage Housing Kit, 1-00-06620

$74.99
SKU 1-00-06620
MPN 1-00-06620

Frequently Bought Together

Description

Replacement Igniter Holder for Harman Replaces part number 1-00-06620 is used on every pellet stove with automatic ignition with these exceptions, please see stove specific notes below.

*Accentra Insert 52i and 52i-TC 2013-2019 had three different burnpot revisions all related to overheating. The Accentra 52i Igniter Cradle: Pre serial 008259179 use 1-00-06620, Post 008259179 use 1-00-574604. There was one burn pot used in the 52i that did not use any igniter cradle.

**Absolute43 and Absolute63 - Latest Burnpot revision use 1-00-777906

***Allure50 uses 1-00-777907


Replacement For Part Number:
  • 1-00-06620

Compatible Models

Helpful Tips

It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Customer Reviews

Based on 1 review Write a review

QUESTIONS & ANSWERS

Have a Question?

Be the first to ask a question about this.

Ask a Question

Net Orders Checkout

Item Price Qty Total
Subtotal $0.00
Shipping
Total

Shipping Address

Shipping Methods