Big Horn Pellet Grill Auger Motor Repair Kit

Get everything you need to repair the pellet grill auger motor; as sometimes, replacing the motor alone may not be sufficient. Our repair kit will bring the pellet feed to its peak efficiency.

This kit uses aftermarket parts where applicable to help you save big!

These are all of the confirmed compatible units for this product. This product may fit others, but these are the only ones we suggest ordering it for at this time.

Check these against the part you are replacing before ordering. If a dimension does not match, contact us and we will confirm the fit.

This product is a kit containing 4 total items.

Component Technical Specs

Open a part to see its specifications.

1 xAuger Bushing For Pellet Grill Push Rod / Shaft

SKU 74076(LBH) (opens in new tab)

Quantity In Kit	1
Length (in)	1 ½"
Width (in)	1 ½"
Height (in)	1"
Outer Diameter (in)	1 ½"
Inner Diameter (in)	½"
Weight	1.00 oz

1 x5 Amp x 20mm -125V Fuse

SKU 1-00-05237 (opens in new tab)

Quantity In Kit	1
Length (in)	¾"
Width (in)	³⁄₁₆"
Height (in)	³⁄₁₆"
Voltage	125
Amperage	5
Weight	0.25 oz

1 xTraeger Pellet Grill 1.6 RPM CW Auger Motor For Most Models

SKU BRN100-AMP(LBH) (opens in new tab)

Quantity In Kit	1
Length (in)	4 ¼"
Width (in)	3 ¼"
Height (in)	2 ¾"
Voltage	120
Amperage	0.26
RPM (Rotations/Minute)	2
Rotation Direction	Clockwise
Frequency (Hz)	60
Wire Connectors	Molex - 2 Pin
Weight	1.00 lbs

1 xPit Boss Auger Motor Shaft Nut & Bolt

Install Instructions For Big Horn Pellet Grill Auger Motor Repair Kit

Instructional Notes

1. On the bottom grate under the hopper, locate the 4 screws that hold it in place and remove them.
2. Remove the 2 screws holding in the controller.
3. Once removed, rotate the controller, so you can push it through where it was housed.
4. Unless already removed, clip the zip ties holding all the wires together.
5. Locate the 4 screws holding the hopper assembly on the grill and remove them (2 on either side).
6. Carefully remove the hopper assembly.
7. When replacing your feed motor, it's a good idea to remove the feed auger from the grill, make the motor swap and then reinstall the feed system as one piece.
8. Remove the 1/4-inch bushing screw (Screw holding the auger to the frame of the grill).
9. Disconnect the red wires from the main harness and loop them back through the burner mount so they are free.
10. With force, try to pull the auger motor back and forth by hand to try to loosen the jam.
11. Once the feed system is out of the grill, using 5/16" (8mm) socket wrench and a 4.5mm allan key, remove the Shear pin, freeing the Auger from the Auger motor.
12. Replace the motor, reconnect the shear pin, install the feeder assembly and lock the bushing in with the set screw. Reconnect your wiring and then reinstall the hopper shell.

How to Remove Auger if it Jams:

1) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord.

2) CAUTION! If the Grill is still hot, allow it to thoroughly cool.

3) Remove any covers necessary to access the Auger Drive Motor.

4) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft and the screw retaining the Auger Bushing into the Auger Tube.

5) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counterclockwise. It will turn hard until it breaks free, then the Auger will turn freely.

6) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger, Auger Tube, and Firepot. (See instructions for proper handling and disposal of ash in Section Five)

7) Sand the outside surfaces of the auger with medium grit sandpaper. Check the inside of the Auger Tube and sand it if needed. Vacuum the sanding grit out of the Auger Tube and Firepot when finished. Check that the Auger rotates freely.

8) Re-attach the Auger shaft to the Auger Drive Motor shaft.

This Item Qualifies For Free Shipping With Orders Over $99!