Camp Chef Pellet Grill Igniter Fits Many Models, PG24-21-AMP


A $40.00 Savings vs the OEM

MPN PG24-21
In Stock
  • Aftermarket Part
  • 220 Watts 120 Volts
  • 30" Wire Lead
  • 3.5 x 3/8" Cartridge
  • Ships FREE with orders over $199
  • 30-Day Hassle Free Returns!
  • 90 Day Warranty Included
  • See Complete Description
Notify Me When Available

Frequently Bought Together


Replacement Igniter For All Camp Chef Grills. 3.5″ x 3/8″ High-density cartridge heating element 220 Watts 120 Volts 30″ wire lead fiberglass insulated Provide continuous sheath temperatures up to 1,200° F

Replacement For Part Number:
  • PG24-21

Click To See Compatible Models

Compatible Models

    Camp Chef

  • Pursuit 20
  • SmokePro DLX 24
  • SmokePro LUX 36
  • SmokePro SE 24
  • SmokePro SG 24
  • SmokePro SGX 36
  • SmokePro STX 24
  • SmokePro XT 24
  • Woodwind Classic 24
  • Woodwind SG 24
  • Woodwind WIFI 20
  • Woodwind WIFI 24
  • Woodwind WIFI 36
  • XXL

Technical Specs

Watts 200
Voltage 120
Length 3-1/2"
Diameter 3/8"
Wire Length 30"
Connector Molex



Assembly Instructions For Camp Chef Pellet Grill Igniter Fits Many Models, PG24-21-AMP

The igniter is located and the end of the pellet burner assembly and is fastened into the burnpot/ fire pot using a set screw. Depending upon your specific model, the process to access this part and replace it may vary slightly from model to model.

  1. Unplug the grill from the power source
  2. Empty any pellets you may have in the hopper
  3. Remove the access panel on the bottom of the hopper if your model has one.
  4. Remove the side screws from the hopper shell and separate the hopper from the burner assembly. You do not need to unplug every wire connection.
  5. Most, if not all models will have the igniter plugged into a purple wire on the controller's main harness. The igniter wire will be the ONLY braided wire connected to the controller (not a plastic coating). Remove the braided wire connection at the Molex disconnect.
  6. Remove all of the cooking grids, drip pan, and baffle from the grill.
  7. Remove the 4 burnpot screws and then wiggle the burnpot free from the burner.
  8. Remove the rubber grommet from the burner assembly where the igniter wires enter into the burner from the hopper side and feed the wires into the burner until the molex connection is in the burner. Remove the burnpot. The igniter wires will pull out through the burner. Now you can loosen the igniter set screw and replace the igniter.
  9. When installing the new igniter, 3/8" to 1/2" of the igniter tip should be visible in the burnpot. Now tighten the set screw.
  10. Set the burnpot into the grill and feed the igniter wires into the burner until the Molex is seen at the passthrough hole and then pull it through. Slip on the ribber grommet and plug the new igniter into the harness.
  11. Pull the slack from the wires as you fit the burnpot into the burner assembly.
  12. Replace the four burnpot screws.
  13. Take up the slack of the burnpot wires and zip tie if needed.
  14. Fit the grommet into the wire hole.
  15. Reposition the hopper back on the burner and secure it with the mounting screws
  16. Replace the hopper bottom access panel if you have one.
  17. Plug in your grill and enjoy.


Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.


Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping With Orders Over $199!

When Will My Order Ship

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 1PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Is Expedited Shipping Available?

We offer both overnight and two day air shipping services for all orders placed within the Continental United States. For information on shipping cut-off times, go to our shipping page.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Read More About Our Shipping Information

Customer Reviews

Based on 18 reviews
Richard D.
Pellet Grill Igniter

I searched the internet to replace my igniter and selected Stove and Grill because of their info on oem and non oem parts. This info gave me confidence that I could purchase this non oem with confidence that it would perform as well as oem. The part was shipped and arrived a few days later and so far is working as expected. I saved $40 on this purchase by using a non oem part.

Rodger S.
Camp Chef Pellet grill igniter replacement

Ordered a replacement igniter for my Camp Chef after burning my out by running out of pellets. Easy install only took 15 minutes.

Pascal M.
Pellet grill hot rod

Exactly what i expected , fits perfect and Delivery was fast .


Rick G.
Camp Chef Pellet Grill Igniter

Part came on time, fits and works perfectly

Alan B.
Excellent service

Each time I have ordered I have located the parts needed. Each time the service is impeccable! I am informed as to all aspects of the order and shipping.