Traeger D2 Auger Motor Kit

Traeger

• Century 885
• Ironwood (Gen 3)
• Ironwood 650
• Ironwood 885
• Pro 575
• Pro 780
• Redland
• Redland XL
• Silverton 620
• Silverton 810
• Silverton XL
• Timberline 1300 DC
• Timberline 850 DC

Pro 575 or Pro 780, Silverton, Century

1. Power off and unplug your grill.
2. Unscrew the two screws on the right side of the hopper and remove the access panel from the bottom of the hopper.
3. Cut the zip ties from both sets of cables.
4. Remove the four screws holding the controller in place.
5. Disconnect the plastic connectors from the controller.
6. Unscrew the four screws that secure the hopper housing to the grill. There are two on the front of the hopper and two on the back.
7. Remove the hopper housing from the auger assembly and set aside.
8. Remove the plastic connector from the auger motor.
9. Remove the four Phillips screws securing the auger motor to the auger assembly, and remove the motor.
10. Remove the bushing screw that secures the auger to the auger tube.
11. Remove the auger from the auger tube and clear out any debris or sawdust.
12. Insert the new auger and follow these steps in reverse to reassemble your grill.

Ironwood or Timberline

1. Power off and unplug your grill.
2. Remove the access panel from the bottom of the hopper by removing the four Phillips screws.
3. Unplug the plastic connector from the auger motor.
4. Remove the auger motor by unscrewing the four Philips-head screws holding it in place.
5. Remove the set screw located on the underside of the auger tube.
6. Slide the auger out of the shaft and clean out any remaining debris.
7. Insert the new auger and follow the previous steps in reverse to reassemble.

'CLEAR AUGER' FUNCTION

The easiest way to clear an auger jam in a WiFIRE-enabled (D2) grill is to use the built-in Clear Auger Jam function.When the user runs a Clear Auger command from the menu, the auger turns backward at full speed for ten seconds, pauses for one second, turns forwards for twelve seconds, pauses for one second, and repeats until the user cancels the operation from the menu.

1. Remove your grill grates, drip tray and heat baffle.
2. Clean out the firepot, vacuuming out any ash buildup.
3. Empty the hopper. If the pellets are swollen from moisture, discard the pellets.
4. navigate to Menu > Auger > Clear Auger.
5. Once the auger is clear, select Cancel on your controller.
6. Replace the heat baffle, drip tray and grill grates.
7. Refill the hopper with fresh pellets.

IF 'CLEAR AUGER' DOES NOT WORK

If the Clear Auger function does not clear out the pellets successfully, or if the auger will not move, you will need to clear the Auger jam manually. 4

To clear an auger jam manually, you will need to access the auger motor. If you need assistance understanding how to access the motor, please contact Customer Service.

How to Clear an Auger Jam Manually

1. Remover the lower panel underneath the hopper. This allows access to Auger Motor.
2. Remove the 4 bolts holding the Auger Motor to the grill frame.
3. Loosen the small screw that locates the Auger bushing.
4. Pull Auger, Motor, and Bushing out of the grill.
5. Clean any debris from Auger.

Re-install the Auger Motor

1. Put Bushing, Auger, and Motor back into the grill.
2. Tighten the small screw that locates the Auger bushing.

• If the bushing is not lined up with the bushing retention screw, the auger gets jammed/pinched in the bushing and won't turn.

1. Re-install the 4 bolts holding the Auger Motor to the grill frame.
2. Re-install panel underneath the hopper.

This Item Qualifies For Free Shipping!