Quadrafire Loop Igniter 300 Watts (Pre 5/2009): 812-3811

$59.99
SKU 812-3811
MPN SRV7000-647
Notify Me When Available

Frequently Bought Together

Description

QuadraFire 300 Watt Loop igniter without wire terminal disconnects. This igniter was used on the Contour, 1100i insert, and the CB1200 stoves and inserts made prior to 2009. These stoves were also shipped with a spare igniter in the accessory package.

This igniter does not have wire terminals and is intended to connect to the ignition wires using two ceramic nuts in the ash pan area.


 

Spare wire and ceramic nuts, part 812-4520

Spare ceramic nuts, part 812-0730


Replacement For Part Number :
  • SRV7000-647


UPC #: 652174167548

Compatible Models

    Quadra-Fire

  • 1000 FS
  • 1100i
  • 800 F/S Nova
  • Classic Bay 1200
  • Classic Bay 1200i
  • Contour
  • Edge 60
  • Mt Vernon AE Insert
  • Mt Vernon AE
  • Mt Vernon E2 FS
  • Trekker

    Quadrafire

  • Trekker Insert

Technical Specs

Watts 300
Length 4 3/8″ Length
Width 3/4″ Wide
Connectors Wires with no connectors
1/4″ Diameter Rod

Instructions

Assembly Instructions For Quadrafire Loop Igniter 300 Watts (Pre 5/2009): 812-3811

  1. The ash drawer is located in the pedestal. To remove, open both the left and right side pedestal access doors. They are hinged in the back and held closed magnetically. Pull out on the back of the over-center style latch and then pivot the holding rod out of the drawer notch on both sides. Pull the ash drawer straight out of the pedestal.
  2. Using a Phillips head screwdriver, remove the (2) two screws that secure the front panel access located just underneath the ash catcher in front of the fi repot. With the access panel removed, the ignition chamber on the fi repot and the wiring are now exposed. The wires are connected together with (2) two ceramic wire nuts. There is approximately 6 inches of wire between the igniter element and the wire nuts. Holding the wire nuts (notice location), pull just enough wire out the of the stove for easy access.
  3. Holding the wires, turn the wire nut counter-clockwise to remove the wire nuts.
  4. With wire nuts removed and wires separated; remove the igniter from the chamber. Using the Phillips screwdriver, remove the single screw and slide the igniter out.
  5. Install the new igniter into the chamber.
  6. Reconnect the wires to the two leads in any order.
  7. Reinstall the ceramic wire nuts by turning clockwise.
  8. Relocate the wires in their original position and operate the firepot cleaning rod while watching for any interference (adjust wire location if necessary).
  9. Reinstall access panel and ash drawer and reconnect to power.

Troubleshooting

It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping With Orders Over $199!

When Will My Order Ship

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 1PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Is Expedited Shipping Available?

We offer both overnight and two day air shipping services for all orders placed within the Continental United States. For information on shipping cut-off times, go to our shipping page.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

If you wish to calculate shipping for an item which does not qualify for free shipping, or if you would like the cost to expedite your order, please do the following. Add the item you want to order to your cart and click here to be taken to the cart page where you can enter your country, state / province, and zip code for an estimate.

Shipping Time Estimations

For information on shipping time estimations, see either the Shipping Information & Transit Times on the cart page, or go to our shipping page.

Read More About Our Shipping Information

Customer Reviews

Based on 3 reviews
100%
(3)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
F
F.S.
Themostat

Good service. Product was delivered on time and quick. Thank You

A
A.
Loop lighter

My experience with the product was great. I was able to fix the problem. Thank you

J
J.B.
Great service

Processed and sent my order on the same day. Thanks!

QUESTIONS & ANSWERS

Have a Question?

Be the first to ask a question about this.

Ask a Question

Net Orders Checkout

Item Price Qty Total
Subtotal $0.00
Shipping
Total

Shipping Address

Shipping Methods