Replacement igniter cartridge for Lennox pellet stoves.
A new igniter cartridge for Lennox pellet stoves will make lighting your pellet stove fast and easy. This igniter cartridge installs in seconds and comes fully assembled. Our electric heater igniter cartridge easily mounts to your stove allowing the cartridge to protect the igniter from excessive heat and debris. Igniter cartridges tend to wear out over time, so it's important to replace it with a quality igniter you can rely on. The igniter cartridge is made from durable materials and guaranteed to provide a perfect fit.
Replacing the H8127, H8127-AMP igniter in a Whitfield or Lennox/ IronStrike Montage pellet stove:
Unplug the stove
Remove the rear service panel
Remove the auger motor from the shaft and remove auger mounting plate
On some models and the tools you may be using, the igniter can also be accessed from the left side by removing the room blower
Locate the igniter under the hopper, it will have white braided wires
Disconnect wires from old igniter and remove the igniter from the stove
using a 5/8" wrench, loosen igniter fitting by turning it CCW
There will be a red wire with a black cap attached to the igniter wires, this is an inline fuse and must be checked. If the fuse is blown, replace it.
Reinstall all items in the reverse order.
Troubleshooting
Replacing the H8127, H8127-AMP igniter in a Whitfield or Lennox/ IronStrike Montage pellet stove:
Sometimes the igniter fitting can be very difficult to crack loose, if this is the case, cut the old igniter wires as close to the fitting as possible and use a 5/8" deep-well socket and a breaker bar to crack the fitting loose
Always insert the new igniter and hand tighten it by hand to avoid crossing the threads
Stoves equipped with an igniter, especially older Whitfields, must have an igniter present in the igniter tube when the stove is operating. If you decide to use the stove without auto ignition for whatever reason, do no operate the stove without an ignition cartridge in the igniter tube, it will not burn properly
It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.
Troubleshooting Igniters:
Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.
For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”
If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.
Warranty
Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers
make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please
be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.
Shipping Information
This Item Qualifies For Free Shipping With
Orders Over $49!
When Will My Order Ship?
All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.
Do You Offer Express Shipping?
Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.
How Does Free Shipping Work?
Most orders over $49 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.
Do You Ship To Canada?
We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.
Do You Ship To Alaska Or Hawaii?
We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.
Do You Ship Outside The US Or Canada?
Unfortunately, at this time we do not offer international shipping other than to Canada.
Shipping Time Estimations
For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.
Replacement igniter cartridge for Lennox pellet stoves.
A new igniter cartridge for Lennox pellet stoves will make lighting your pellet stove fast and easy. This igniter cartridge installs in seconds and comes fully assembled. Our electric heater igniter cartridge easily mounts to your stove allowing the cartridge to protect the igniter from excessive heat and debris. Igniter cartridges tend to wear out over time, so it's important to replace it with a quality igniter you can rely on. The igniter cartridge is made from durable materials and guaranteed to provide a perfect fit.
Replacing the H8127, H8127-AMP igniter in a Whitfield or Lennox/ IronStrike Montage pellet stove:
Unplug the stove
Remove the rear service panel
Remove the auger motor from the shaft and remove auger mounting plate
On some models and the tools you may be using, the igniter can also be accessed from the left side by removing the room blower
Locate the igniter under the hopper, it will have white braided wires
Disconnect wires from old igniter and remove the igniter from the stove
using a 5/8" wrench, loosen igniter fitting by turning it CCW
There will be a red wire with a black cap attached to the igniter wires, this is an inline fuse and must be checked. If the fuse is blown, replace it.
Reinstall all items in the reverse order.
Troubleshooting
Replacing the H8127, H8127-AMP igniter in a Whitfield or Lennox/ IronStrike Montage pellet stove:
Sometimes the igniter fitting can be very difficult to crack loose, if this is the case, cut the old igniter wires as close to the fitting as possible and use a 5/8" deep-well socket and a breaker bar to crack the fitting loose
Always insert the new igniter and hand tighten it by hand to avoid crossing the threads
Stoves equipped with an igniter, especially older Whitfields, must have an igniter present in the igniter tube when the stove is operating. If you decide to use the stove without auto ignition for whatever reason, do no operate the stove without an ignition cartridge in the igniter tube, it will not burn properly
It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.
Troubleshooting Igniters:
Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.
For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”
If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.
Warranty
Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers
make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please
be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.
Shipping Info
This Item Qualifies For Free Shipping With
Orders Over $49!
When Will My Order Ship?
All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.
Do You Offer Express Shipping?
Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.
How Does Free Shipping Work?
Most orders over $49 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.
Do You Ship To Canada?
We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.
Do You Ship To Alaska Or Hawaii?
We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.
Do You Ship Outside The US Or Canada?
Unfortunately, at this time we do not offer international shipping other than to Canada.
Shipping Time Estimations
For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.
Much cheaper than the OEM version. Quick stove start, ignites faster than I thought it would. Will be comming back for my stove parts.
D
Donald W.
Works as it Should
Installed like OEM and lit right up
V
Vincent G.
Great product and service
Part was delivered in a timely manner and worked as it should.
R
Réjean B.
Service excellent et rapide
T
Terry C.
Not used yet
I have not used these and I’m hoping I won’t start using them for a couple of more years. I bought them as spares. I usually get between two and three years out of a good igniter. I am hoping because these are American made that they are as good as the ones that are four times more expensive.
Much cheaper than the OEM version. Quick stove start, ignites faster than I thought it would. Will be comming back for my stove parts.
D
Donald W.
Works as it Should
Installed like OEM and lit right up
V
Vincent G.
Great product and service
Part was delivered in a timely manner and worked as it should.
R
Réjean B.
Service excellent et rapide
T
Terry C.
Not used yet
I have not used these and I’m hoping I won’t start using them for a couple of more years. I bought them as spares. I usually get between two and three years out of a good igniter. I am hoping because these are American made that they are as good as the ones that are four times more expensive.
