Skip to main content
Skip to main content
Product title:

Castle Pellet Stove Igniter: 720307-AMP

Product rating:
Product price:
$39.99

A $40.00 Savings over the OEM

Product SKU ! 720307-AMP
Product MPN ! 720307
Product availability: In Stock
Bullet point features

Frequently Bought Together

Total Price: $76.97

Description

Castle Serenity Pellet Stove Igniter. The Igniter / Hot Rod works by superheating the air that passes through the burn pot.  This super-heated air comes in contact with the pellets causing ignition. Typically, it takes the igniter around 2-2½ minutes to reach its max temperature and begin to glow.  

 




Replacement For Part Number:

  • 720307

View Compatible Models

Compatible Models

    Castle

  • HPS10IC
  • Serenity

Technical Specs

Igniter Length 6"
Wire Length 10"

Instructions

Install Instructions For Castle Pellet Stove Igniter: 720307-AMP

Igniter Installation:

1.) Unplug the stove from the wall outlet.

2.) Remove the side panel of the stove closest to the power supply.

3.) Unplug the igniter from the wiring harness.

4.) Remove the 4mm set screw from the ignitor assembly.

5.) Pull the entire assembly from the ignitor tube.

6.) Reattach the two-piece moon clamp bracket around the igniter and slide it back into the ignitor tube.

7.) Position the tip of the igniter to sit centered in the tube (Make sure the tip of the igniter sits 1/2" or less from the opening).

8.) Snug the 4 mm set screw in place (Do not over-tighten).

9.) Reconnect the ignitor wires to the wiring harness

10.) Reinstall the side panel

11.) Plug in the unit.


Click on Videos if you need further assistance.


Troubleshooting

Helpful Tip:

It is important to make sure your burn pot and venting are clean. A build-up of carbon or ash in the burn pot or venting system can restrict airflow through the unit. Often the igniter is working fine, and this restriction in airflow is what causes the stove not to ignite.

Click to view: "ComfortBilt's Guide to Igniter Testing" or "ComfortBilt's Guide to Cleaning"


It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Information

This Item Qualifies For Free Shipping With Orders Over $49!

HOLIDAY UPDATE
Due to the upcoming Christmas and New Years holidays, shippers will not be picking up on the dates below. Additionally, packages may take longer to arrive than expected. We appreciate your understanding and patience during this time.

  • USPS: No pickup on Dec 24th, Dec 25th, and Jan 1st.
  • UPS: No pickup on Dec 24th (except NDA and 2nd Day), Dec 25th, Dec 31st (except NDA and 2nd Day), and Jan 1st.
CANADA UPDATE

Due to the ongoing Canada Post postal workers' strike, we are forced to suspend all ordering to Canada. Please be advised that any shipments that did not clear U.S. customs by November 15th will be delayed until Canada Post is fully operational. We appreciate your understanding and patience during this time.

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $49 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information
Jump back to product information tab navigation

Description

Castle Serenity Pellet Stove Igniter. The Igniter / Hot Rod works by superheating the air that passes through the burn pot.  This super-heated air comes in contact with the pellets causing ignition. Typically, it takes the igniter around 2-2½ minutes to reach its max temperature and begin to glow.  

 




Replacement For Part Number:

  • 720307

View Compatible Models

Technical Specs

Igniter Length 6"
Wire Length 10"

Instructions

Install Instructions For Castle Pellet Stove Igniter: 720307-AMP

Igniter Installation:

1.) Unplug the stove from the wall outlet.

2.) Remove the side panel of the stove closest to the power supply.

3.) Unplug the igniter from the wiring harness.

4.) Remove the 4mm set screw from the ignitor assembly.

5.) Pull the entire assembly from the ignitor tube.

6.) Reattach the two-piece moon clamp bracket around the igniter and slide it back into the ignitor tube.

7.) Position the tip of the igniter to sit centered in the tube (Make sure the tip of the igniter sits 1/2" or less from the opening).

8.) Snug the 4 mm set screw in place (Do not over-tighten).

9.) Reconnect the ignitor wires to the wiring harness

10.) Reinstall the side panel

11.) Plug in the unit.


Click on Videos if you need further assistance.


Troubleshooting

Helpful Tip:

It is important to make sure your burn pot and venting are clean. A build-up of carbon or ash in the burn pot or venting system can restrict airflow through the unit. Often the igniter is working fine, and this restriction in airflow is what causes the stove not to ignite.

Click to view: "ComfortBilt's Guide to Igniter Testing" or "ComfortBilt's Guide to Cleaning"


It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping With Orders Over $49!

HOLIDAY UPDATE
Due to the upcoming Christmas and New Years holidays, shippers will not be picking up on the dates below. Additionally, packages may take longer to arrive than expected. We appreciate your understanding and patience during this time.

  • USPS: No pickup on Dec 24th, Dec 25th, and Jan 1st.
  • UPS: No pickup on Dec 24th (except NDA and 2nd Day), Dec 25th, Dec 31st (except NDA and 2nd Day), and Jan 1st.
CANADA UPDATE

Due to the ongoing Canada Post postal workers' strike, we are forced to suspend all ordering to Canada. Please be advised that any shipments that did not clear U.S. customs by November 15th will be delayed until Canada Post is fully operational. We appreciate your understanding and patience during this time.

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $49 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information

Customer Reviews

Based on 38 reviews
100%
(38)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
S
Sheila B.

Wonderful customer service.

j
jon b.
Igniter castle pellet stove

Parts in stock a plus. Lost in shipment by carrier. Company took responsibility and shipped another one no problem. Install was fine. Part works as advertised
Customer support better than most.

P
Pat P.

Was so easy to order from your web sight. Was very impressed with how informed I was kept on sending and receiving of item came in a timely manner. Thank you for great service. Pat Petty

B
Bradley B.

Great service Great price Quick shipping

S
Stephen E.
Exactly what was needed

Bought an igniter for our pellet stove. Very easy to find on the website, fast shipping, will use again

123

QUESTIONS & ANSWERS

If your question does not concern this specific product, use our contact form

Have a Question?

Be the first to ask a question about this.

Ask a Question

Customer Reviews

Based on 38 reviews
100%
(38)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
S
Sheila B.

Wonderful customer service.

j
jon b.
Igniter castle pellet stove

Parts in stock a plus. Lost in shipment by carrier. Company took responsibility and shipped another one no problem. Install was fine. Part works as advertised
Customer support better than most.

P
Pat P.

Was so easy to order from your web sight. Was very impressed with how informed I was kept on sending and receiving of item came in a timely manner. Thank you for great service. Pat Petty

B
Bradley B.

Great service Great price Quick shipping

S
Stephen E.
Exactly what was needed

Bought an igniter for our pellet stove. Very easy to find on the website, fast shipping, will use again

123
Liquid error (layout/theme line 255): Could not find asset snippets/iStock-notify-me.liquid