Skip to main content
Skip to main content
Product title:

Castle Pellet Stove Igniter: 720307-AMP

Product rating:
Product price:
Save 33%
$49.99
$33.74

A $20.25 Savings over the OEM

Product SKU ! 720307-AMP
Product MPN ! 720307
Product availability: In Stock
Bullet point features
Buy Now Pay Later

Frequently Bought Together

Total Price: $67.47

Description

Castle Serenity Pellet Stove Igniter. The Igniter / Hot Rod works by superheating the air that passes through the burn pot.  This super-heated air comes in contact with the pellets causing ignition. Typically, it takes the igniter around 2-2½ minutes to reach its max temperature and begin to glow.  

 




Replacement For Part Number:

  • 720307

Compatible Models

Technical Specs

Length (in) 6"
Width (in) ½"
Height (in) ½"
Outer Diameter (in) ½"
Voltage 115
Power type AC
Wattage 350
Wire Connectors Molex
Igniter Length 6"
Wire Length 10"
Weight 2.25 oz

Instructions

Install Instructions For Castle Pellet Stove Igniter: 720307-AMP

Instructional Documents:

Instructional Videos:

Igniter Installation:

1.) Unplug the stove from the wall outlet.

2.) Remove the side panel of the stove closest to the power supply.

3.) Unplug the igniter from the wiring harness.

4.) Remove the 4mm set screw from the ignitor assembly.

5.) Pull the entire assembly from the ignitor tube.

6.) Reattach the two-piece moon clamp bracket around the igniter and slide it back into the ignitor tube.

7.) Position the tip of the igniter to sit centered in the tube (Make sure the tip of the igniter sits 1/2" or less from the opening).

8.) Snug the 4 mm set screw in place (Do not over-tighten).

9.) Reconnect the ignitor wires to the wiring harness

10.) Reinstall the side panel

11.) Plug in the unit.


Click on Videos if you need further assistance.


Troubleshooting

Helpful Tip:

It is important to make sure your burn pot and venting are clean. A build-up of carbon or ash in the burn pot or venting system can restrict airflow through the unit. Often the igniter is working fine, and this restriction in airflow is what causes the stove not to ignite.

Click to view: "ComfortBilt's Guide to Igniter Testing" or "ComfortBilt's Guide to Cleaning"


It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Information

This Item Qualifies For Free Shipping With Orders Over $99!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package. Please note, we are unable to track US Postal packages once they cross the US border and cannot guarantee shipping times. All customs fees incurred are the responsibility of the customer and are not included in the total price. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information
Jump back to product information tab navigation

Description

Castle Serenity Pellet Stove Igniter. The Igniter / Hot Rod works by superheating the air that passes through the burn pot.  This super-heated air comes in contact with the pellets causing ignition. Typically, it takes the igniter around 2-2½ minutes to reach its max temperature and begin to glow.  

 




Replacement For Part Number:

  • 720307

Technical Specs

Length (in) 6"
Width (in) ½"
Height (in) ½"
Outer Diameter (in) ½"
Voltage 115
Power type AC
Wattage 350
Wire Connectors Molex
Igniter Length 6"
Wire Length 10"
Weight 2.25 oz

Instructions

Install Instructions For Castle Pellet Stove Igniter: 720307-AMP

Instructional Documents:

Instructional Videos:

Igniter Installation:

1.) Unplug the stove from the wall outlet.

2.) Remove the side panel of the stove closest to the power supply.

3.) Unplug the igniter from the wiring harness.

4.) Remove the 4mm set screw from the ignitor assembly.

5.) Pull the entire assembly from the ignitor tube.

6.) Reattach the two-piece moon clamp bracket around the igniter and slide it back into the ignitor tube.

7.) Position the tip of the igniter to sit centered in the tube (Make sure the tip of the igniter sits 1/2" or less from the opening).

8.) Snug the 4 mm set screw in place (Do not over-tighten).

9.) Reconnect the ignitor wires to the wiring harness

10.) Reinstall the side panel

11.) Plug in the unit.


Click on Videos if you need further assistance.


Troubleshooting

Helpful Tip:

It is important to make sure your burn pot and venting are clean. A build-up of carbon or ash in the burn pot or venting system can restrict airflow through the unit. Often the igniter is working fine, and this restriction in airflow is what causes the stove not to ignite.

Click to view: "ComfortBilt's Guide to Igniter Testing" or "ComfortBilt's Guide to Cleaning"


It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping With Orders Over $99!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package. Please note, we are unable to track US Postal packages once they cross the US border and cannot guarantee shipping times. All customs fees incurred are the responsibility of the customer and are not included in the total price. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information

Customer Reviews

Based on 55 reviews
100%
(55)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
A
Anthony J.F.
Arrived as a back up for me

looks fine, it will hopefully work when I install it, when the one goes out that I just put in

R
Roger K.
Arrived on time

I replaced the last igniter a year ago and it still works fine but I got to thinking what if the igniter went out and I didn't have a backup? That's where Stove and Grill came in perfectly. The igniters arrived on time even tho I don't need one yet. I'll keep going to Stove and Grill for any stove parts that I might need in the future..

D
Dennis E.
works great

Of course these parts seem to give out during the coldest times, however had one on hand and was able to replace before we noticed the cold. They always seem to have the part you're looking for.

D
Doug W.
Worked like a charm

This part was easy to install in my pellet stove and I will definitely return to order other part in the future.

E
Edward N.
Igniter

My igniter had went out on my HP22 which was my spare that I never replenished. I ordered a new one, I payed extra for shipping but I believe it was delivered to my home in washington state in 4 days. I installed and up and running again before the holidays. Thank you for the fast service

123

QUESTIONS & ANSWERS

If your question does not concern this specific product, use our contact form

Have a Question?

Be the first to ask a question about this.

Ask a Question

Customer Reviews

Based on 55 reviews
100%
(55)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
A
Anthony J.F.
Arrived as a back up for me

looks fine, it will hopefully work when I install it, when the one goes out that I just put in

R
Roger K.
Arrived on time

I replaced the last igniter a year ago and it still works fine but I got to thinking what if the igniter went out and I didn't have a backup? That's where Stove and Grill came in perfectly. The igniters arrived on time even tho I don't need one yet. I'll keep going to Stove and Grill for any stove parts that I might need in the future..

D
Dennis E.
works great

Of course these parts seem to give out during the coldest times, however had one on hand and was able to replace before we noticed the cold. They always seem to have the part you're looking for.

D
Doug W.
Worked like a charm

This part was easy to install in my pellet stove and I will definitely return to order other part in the future.

E
Edward N.
Igniter

My igniter had went out on my HP22 which was my spare that I never replenished. I ordered a new one, I payed extra for shipping but I believe it was delivered to my home in washington state in 4 days. I installed and up and running again before the holidays. Thank you for the fast service

123