Skip to main content
Skip to main content
Product title:

Harman Absolute 43 Igniter Bracket: 1-00-777906

Product rating:
Product price:
$49.99
Product SKU ! 1-00-777906
Product MPN ! 1-00-777906
Only 3 Left In Stock
Bullet point features

Buy 2 Save 10%. Buy 3+ save 15%!

Description

Harman Pellet Stove Igniter Bracket for the Absolute 43.  The igniter bracket holds the igniter in proper position inside the neck of the burn pot.  It is important to periodically inspect this bracket.  If the bracket is not seated correctly or is warped, it may cause ignition issues. 

Note: Many Changes were made to the absolute 43 burn pot.  It is important to confirm that you have the correct burn pot that will accept this bracket.

July 2018 Ending Manufacturing Date: Active


Replacement For Part Number:

  • 1-00-777906

UPC: 652174923700

Compatible Models

    Harman

  • Absolute 43-C

Technical Specs

Videos

Instructions

Install Instructions For Harman Absolute 43 Igniter Bracket: 1-00-777906

Igniter Cradle/Holder Installation Instructions:


1.) The igniter cradle/holder is located in the burn pot. (To access the cradle you must loosen the two wing nuts securing the burn pot clean-out cover to the bottom of the pot. Once both wing nuts are loosened the cover plate can be removed).

2.) From the front of the stove, remove the two 5/16" or 8mm screws that hold the igniter cradle inside the burn pot. This will allow the cradle to drop out (Do not discard these screws).

3.) To remove the igniter from the old-style cradle/holder, twist the two tabs that secure the flat plate to the ignitor. Your old igniter can now be removed (Pay special attention to how the ignitor is positioned in the cradle).

4.) Position your ignitor into the new cradle (If you are replacing the igniter at this time follow the instructions below on igniter replacement).

5.) Position the new cradle/holder in the same orientation as the previous holder and install the cradle using the two 5/16" or 8mm mounting screws (Updated cradles do not have a retainer plate).

6.) The new cradle/holder will have 2 holes for additional screws under the ignitor. Gently tighten these screws. This will push the igniter against the bottom of the burn pot (Do not over-tighten these screws).





Igniter Installation Instructions:


1.) The igniter is located in the burn pot. (To access the ignitor you must first loosen the two wing nuts securing the burn pot clean-out cover to the bottom of the pot. Once both wing nuts are loosened the cover plate can be removed).


2.) The igniter is accessed and changed through the front of the stove, but you will also need to access the rear of the stove to free the wiring.


3.) From the rear of the unit, locate the yellow and light blue wires for the igniter at the point where they pass through the neck of the burn pot into the rear of the stove, it is directly under the auger (On freestanding stoves this will require that the rear / side shields are removed. When replacing the ignitor on an insert the unit will need to be slid forward and pulled out of the firebox. On some units, there may be a small rubber grommet or a dab of high temp silicone where the ignitor wires transition to the back of the unit.)


4.) In this area you should notice extra wire looped together (Likely, this excess wire will be secured in position with a zip tie). This extra wire needs to be freed up so that the disconnects can be pulled forward and disconnected from the neck of the burn pot. This can be done by carefully cutting the zip tie and gently pushing about 12" of the yellow and light blue wire into the cavity of the stove where the ignitor is located.


5.) From the front of the stove, remove the two 5/16" or 8mm screws that hold the igniter cradle inside the burn pot (Do not discard these screws).

 

 6.) Drop the igniter assembly down and pull it forward until you can see the wire disconnects, then disconnect the wires from the harness and remove the whole assembly.

 

7.) To remove the igniter from the (old style) cradle, twist the two tabs that secure the flat plate to the ignitor. Your old igniter can now be removed (Pay special attention to how the ignitor is positioned in the cradle. The replacement will be positioned in the same way).


8.) Position your new ignitor in the cradle and reinstall the cradle using the two 5/16" or 8mm mounting screws (The updated cradle does not have a retainer plate).

 

9.) From the rear of the unit, gently pull the excess wire you previously feed forward to remove the slack, coil the extra wire length, and secure it with a zip tie.


10.) Reinstall the cover plate and test your ignitor to ensure it is operating correctly.

Troubleshooting

Airflow:

-It is important to make sure your burn pot and venting are clean. A build-up of carbon or ash in the burn pot or venting system can restrict airflow through the unit. Often the igniter is working fine, and this restriction in airflow is what causes issues with ignition. If these areas of the stove are clean and your stove will not ignite or there is a long delay during ignition you should inspect your door gasket, door latch, and burn pot ignitor cover. If the door does not make a tight seal, air can be drawn into the stove through this area instead of being pulled through the neck of the burn pot and across the ignitor.


Control Board Display:

-Check your control to make sure your stove is not in the "manual" mode. The auto ignite option MUST be selected in order to allow the control board to send power to the element.



Check The Burn Pot:

-If the ignitor light is illuminated on your control, the unit feeds fuel but the pellets do not ignite, open the door and *carefully* feel around the burn pot to see if you can sense any warmth. If you do not feel any warmth or see a visible glow it's likely that the ignitor has failed. If you feel warmth/heat around the burn pot it is possible that you have an airflow issue, build-up in the holes in the burn pot / around the ignitor, or you may have an issue with the ignitor cradle/ holder.


Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Information

This Item Qualifies For Free Shipping With Orders Over $99!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information
Jump back to product information tab navigation

Description

Harman Pellet Stove Igniter Bracket for the Absolute 43.  The igniter bracket holds the igniter in proper position inside the neck of the burn pot.  It is important to periodically inspect this bracket.  If the bracket is not seated correctly or is warped, it may cause ignition issues. 

Note: Many Changes were made to the absolute 43 burn pot.  It is important to confirm that you have the correct burn pot that will accept this bracket.

July 2018 Ending Manufacturing Date: Active


Replacement For Part Number:

  • 1-00-777906

UPC: 652174923700

Instructions

Assembly Instructions For Harman Absolute 43 Igniter Bracket: 1-00-777906

Igniter Cradle/Holder Installation Instructions:


1.) The igniter cradle/holder is located in the burn pot. (To access the cradle you must loosen the two wing nuts securing the burn pot clean-out cover to the bottom of the pot. Once both wing nuts are loosened the cover plate can be removed).

2.) From the front of the stove, remove the two 5/16" or 8mm screws that hold the igniter cradle inside the burn pot. This will allow the cradle to drop out (Do not discard these screws).

3.) To remove the igniter from the old-style cradle/holder, twist the two tabs that secure the flat plate to the ignitor. Your old igniter can now be removed (Pay special attention to how the ignitor is positioned in the cradle).

4.) Position your ignitor into the new cradle (If you are replacing the igniter at this time follow the instructions below on igniter replacement).

5.) Position the new cradle/holder in the same orientation as the previous holder and install the cradle using the two 5/16" or 8mm mounting screws (Updated cradles do not have a retainer plate).

6.) The new cradle/holder will have 2 holes for additional screws under the ignitor. Gently tighten these screws. This will push the igniter against the bottom of the burn pot (Do not over-tighten these screws).





Igniter Installation Instructions:


1.) The igniter is located in the burn pot. (To access the ignitor you must first loosen the two wing nuts securing the burn pot clean-out cover to the bottom of the pot. Once both wing nuts are loosened the cover plate can be removed).


2.) The igniter is accessed and changed through the front of the stove, but you will also need to access the rear of the stove to free the wiring.


3.) From the rear of the unit, locate the yellow and light blue wires for the igniter at the point where they pass through the neck of the burn pot into the rear of the stove, it is directly under the auger (On freestanding stoves this will require that the rear / side shields are removed. When replacing the ignitor on an insert the unit will need to be slid forward and pulled out of the firebox. On some units, there may be a small rubber grommet or a dab of high temp silicone where the ignitor wires transition to the back of the unit.)


4.) In this area you should notice extra wire looped together (Likely, this excess wire will be secured in position with a zip tie). This extra wire needs to be freed up so that the disconnects can be pulled forward and disconnected from the neck of the burn pot. This can be done by carefully cutting the zip tie and gently pushing about 12" of the yellow and light blue wire into the cavity of the stove where the ignitor is located.


5.) From the front of the stove, remove the two 5/16" or 8mm screws that hold the igniter cradle inside the burn pot (Do not discard these screws).

 

 6.) Drop the igniter assembly down and pull it forward until you can see the wire disconnects, then disconnect the wires from the harness and remove the whole assembly.

 

7.) To remove the igniter from the (old style) cradle, twist the two tabs that secure the flat plate to the ignitor. Your old igniter can now be removed (Pay special attention to how the ignitor is positioned in the cradle. The replacement will be positioned in the same way).


8.) Position your new ignitor in the cradle and reinstall the cradle using the two 5/16" or 8mm mounting screws (The updated cradle does not have a retainer plate).

 

9.) From the rear of the unit, gently pull the excess wire you previously feed forward to remove the slack, coil the extra wire length, and secure it with a zip tie.


10.) Reinstall the cover plate and test your ignitor to ensure it is operating correctly.

Troubleshooting

Airflow:

-It is important to make sure your burn pot and venting are clean. A build-up of carbon or ash in the burn pot or venting system can restrict airflow through the unit. Often the igniter is working fine, and this restriction in airflow is what causes issues with ignition. If these areas of the stove are clean and your stove will not ignite or there is a long delay during ignition you should inspect your door gasket, door latch, and burn pot ignitor cover. If the door does not make a tight seal, air can be drawn into the stove through this area instead of being pulled through the neck of the burn pot and across the ignitor.


Control Board Display:

-Check your control to make sure your stove is not in the "manual" mode. The auto ignite option MUST be selected in order to allow the control board to send power to the element.



Check The Burn Pot:

-If the ignitor light is illuminated on your control, the unit feeds fuel but the pellets do not ignite, open the door and *carefully* feel around the burn pot to see if you can sense any warmth. If you do not feel any warmth or see a visible glow it's likely that the ignitor has failed. If you feel warmth/heat around the burn pot it is possible that you have an airflow issue, build-up in the holes in the burn pot / around the ignitor, or you may have an issue with the ignitor cradle/ holder.


Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping With Orders Over $99!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

QUESTIONS & ANSWERS

If your question does not concern this specific product, use our contact form

Have a Question?

Be the first to ask a question about this.

Ask a Question

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)