Heatilator Eco Choice Combustion Blower Exhaust Fan Motor: 3-21-08639-AMP

This exhaust blower motor is extremely durable and is used on many Heatilator Eco Choice pellet stoves.  Some pellet stoves had an older version of this blower that looked much different. This motor design is updated as the replacement for all pellet-burning stoves. The blower motor comes with wire terminals and plugs directly into existing connections for all models.

This blower motor DOES NOT come with an impeller. It is advisable to purchase an impeller when replacing this blower as the old impeller from your existing blower may not come off the shaft (seized) or it may be damaged in the process of removing the blower.

• If you have BA100, BH60, BH105 then you need 5" double paddle blade impeller, part # 3-20-502221
• If you have BIO-120 then you need 4 3/4" Single paddle blade impeller, part # 3-21-00661

Heatilator Eco Choice uses a threaded mounting post to secure most of their combustion motors which can become stripped. They are sold individually and each motor uses three (3) Part # 1-00-53483208

Here are the nuts that thread on to the posts, Part # HDW600

Replacement For Part Number:

• 3-21-08639

View Compatible Models

UPC: 652174686957

Volts	120
Amps	1.17
Cycles	60 Hz
RPM	3000
Shaft Diameter	5/16"
Shaft Length	1-13/16"
Wiring Connectors	3-Wire Pig-tail with 1/4" female spades

Install Instructions For Heatilator Eco Choice Combustion Blower Exhaust Fan Motor: 3-21-08639-AMP

This combustion blower is used on many Heatilator Eco Choice pellet stoves so here is a basic overview of what you will need to do:

1. Always disconnect the power to the stove before attempting any service
2. For motors mounted on the stove body, you will need to open the firebox, remove the combustion motor cover, remove the impeller from the motor shaft and then you can remove the motor from the back of the stove.
3. In a perfect scenario, everything comes apart easily, however; the impeller can become seized on the motor shaft if it has never been removed, in which case the shaft of the motor must be cut. This will require a new impeller to be mounted on the new motor so you will want to have one of those on hand. See the description for this b lower to figure out which impeller you need, there are two (2) types to choose from, depending on your stove model. If you need to cut the shaft, a hand-held hacksaw blade is the best tool. It needs to be long and narrow because it need to fit between the motors cooling fan and the stove wall from behind the stove. You will also need to jam a screwdriver or something between the impeller and stove wall in the fire box to keep the shaft from spinning as you cut through the shaft. This same process may need to be done for stoves that use a removable hub but it will be easier because the whole assembly can be removed from the stove when cutting.
4. All of these motors are secured to the stove using threaded studs which pass through the firebox or the hub and are wedged in place. If the stud is spinning when you are trying to remove the nut, the stud must also be cut in the same way as the shaft. This is not as common but it can happen. Links to these studs and replacement nuts are also in the description.
5. Once everything is removed you will install your new studs is needed, install the motor to the stove or hub, install your existing or new impeller and then reconnect all of the wiring.

Solving Combustion Blower Issues

• If your stove is an insert and the venting was not cleaned properly while the stove was pulled out, there’s a good chance that ash fell down and is blocking the combustion blower from spinning.
• If your stove has a combustion motor cover inside the stove, make sure it was put back and secure.
• If your combustion blower is removable, make sure the blower is properly secured and tight-fitting. It is possible on these two stoves improperly install the blower.
• If service was performed on the combustion blower itself, make sure the impeller blades aren’t rubbing against the cover or the cooling fan blades aren’t rubbing on their cover or a pellet isn’t obstructing the cooling fan from turning.
• If wires were disconnected, make sure the combustion blower is plugged into the correct wires.
• If the combustion blower is NOT turning and everything is wired correctly and nothing is obstructing it from turning… AND the Combustion Blower lights are illuminated on the control board, a new combustion blower will need to be installed.

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

This Item Qualifies For Free Shipping With Orders Over $99!

Learn More About Our Shipping Information