Quadra-Fire Mt Vernon AE & Edge 60 Combustion Blower Motor: SRV7000-588M

This is the most recently updated combustion blower motor for the Mt Vernon AE pellet stove, Mt Vernon AE pellet insert, and the Edge60 built-in fireplace. Prior replacement motors came with a housing assembly which is no longer offered.

This motor has a hub with two mounting configurations. The outer holes accommodate newer-style housings that use 6 phillips-head screws to secure the motor.

If you have an older style motor housing, simply remove the 6 off-set screws and nuts attached to the hub of the new motor to accommodate the off-set threaded posts used on the older housings.

This replacement motor comes with a "serviceable" silicone gasket which can survive the process of removing the blower and reinstalling during service intervals. This gasket will accommodate new-style AND the older-style AE combustion motors. Replacement gaskets are SRV7000-714

Right above the combustion motor housing there is an exhaust transition with a clap-style mount, the gasket for this is SRV240-0850.

Combustion/ Exhaust Blower Motor for the Mt Vernon Original Model Pellet Stove (2002-06) is part SRV7000-193

Combustion/ Exhaust Blower Motor for the Mt Vernon E2 Stove/ Insert is part SRV7080-106

Replacement For Part Numbers:

• SRV7000-588M
• 7034-033

View Compatible Models

UPC: 652174943647

Volts	15V DC
Other	Integrated circuitry with internal PCB and microprocessor
Amps	2.2
RPM	Variable Speed/ 3000RPM
Wiring Connectors	Wiring harness

Assembly Instructions For Quadra-Fire Mt Vernon AE & Edge 60 Combustion Blower Motor: SRV7000-588M

Combustion Blower Replacement

1. Shutdown the stove or insert and then unplug it from power.
2. Remove left and right side access panels
3. Remove the combustion blower motor from the housing by loosening the 6 9mm (11/32) hex nuts. It is not necessary or recommended to remove the housing to replace or service the combustion blower.
4. Disconnect the wire from the control board connection points #1 and #8.
5. Install new combustion blower motor. If the gasket between housing and motor is damaged it will have to be replaced, SRV7000-714. A replacement gasket is included with the replacement blower.
6. Reconnect the power and hall sensors to control board inputs #1 and #8

**NOTE The replacement combustion motor hub for the AE units changed from 6 off-set threaded posts attached to the housing to 6 phillip-head screw for the newer style blowers. If you have an old style housing, remove the 6 off-set screws and nuts attached to the blower to mount the replacement motor to the old style housing.**

• Instructions for Quadra-Fire Mt Vernon AE & Edge 60 Combustion Blower Motor: SRV7000-588M

Download the Mt Vernon Troubleshooting Manual

If your combustion blower is not spinning it is either...

• Obstructed -Check blower for obstructions: *Clean fan blades & check fan bearing.
• No Power - Harness - Check blower connections *Color of wires, Connector pins, test for broken wires.
• Overheat Snap Disc - Check over heat snap disc 230-1290, it is located on the pellet drop chute. If the switch is tripped, the center button will depress and "snap" back to closed position when pushed.
• Replace exhaust blower if all previous checks are good.
• If the blower is new and connected properly and it still isn't powering up, replace the control board SRV7000-456

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

This Item Qualifies For Free Shipping!

Learn More About Our Shipping Information