Skip to main content
Skip to main content

Vogelzang Pellet Stove Igniter (250W/300W) C-E-ING / 80607-AMP


A $45.00 Savings vs the OEM

SKU 80607(VOG)-AMP
In Stock
  • Aftermarket Part
  • Ships FREE with orders over $199
  • 30-Day Hassle Free Returns!
  • 90 Day Warranty Included
  • Buy with confidence-Buy with the experts!
  • See Complete Description
Notify Me When Available

Frequently Bought Together


Vogelzang Pellet Stove Igniter (250W/300W).  The igniter allows your unit to auto light when there is a call for heat.  It works by superheating the combustion air coming into the stove just before it enters the burn pot.  If the igniter is not functioning properly you may experience ignition issues.       

Note: From time to time the manufacturer will ship 250-watt igniters as replacement parts.  They also build units with both 300-watt and 250-watt igniters (They are used interchangeably). Either wattage will work without any notable difference.

It is advised to always replace the door gasket whenever an igniter is replaced. air that enters the firebox from the door gasket causes delayed ignitions that ultimately causes igniters to fail. The door gasket for units that use this igniter is part 88066

Replacement For Part Numbers:
  • C-E-IGN
  • 80607

Click To See Compatible Models

Technical Specs

Watts 250 or 300
Length 4"
Diameter 3/8"
Connectors 1/4" Male Spades



Assembly Instructions For Vogelzang Pellet Stove Igniter (250W/300W) C-E-ING / 80607-AMP

  1. Unplug the unit.
  2. Remove the rear service panel (On some models you may need to disconnect the feed motor or blower to access the igniter).
  3. Locate the igniter (The igniter will be located in the center of the unit close to the bottom).
  4. Disconnect the leads supplying power to the igniter.
  5. Remove two bolts attaching the igniter bracket/chamber to the back of the stove.
  6. With the igniter bracket in hand, loosen the set screw that is securing the old igniter in place and remove the igniter.
  7. Position the new igniter into the bracket and tighten the set screw (The end of the igniter should be approximately 1/4" away from the end of the tube).
  8. Reposition the previously removed bracket with the new igniter back in place.
  9. Reinstall the two bolts that attach the ignitor bracket/chamber to the back of the stove.
  10. Reconnect the previously removed leads to the new igniter.
  11. Reinstall any components that were previously removed.
  12. Reposition and attach the service panels.
  13. Plug in the unit and test the igniter.


If your igniter is getting hot but the unit is not lighting, make sure the damper below the burn pot is closed. If you are experiencing ignition times that are longer than usual you should consider replacing your door gasket.

If your igniter is not getting warm, it has most likely failed and will need to be replaced.

Sometimes when an igniter shorts out it will blow the main fuse or the ignition circuit fuse on the controller.

It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.


Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping With Orders Over $199!

When Will My Order Ship

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 1PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Is Expedited Shipping Available?

We offer both overnight and two day air shipping services for all orders placed within the Continental United States. For information on shipping cut-off times, go to our shipping page.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Read More About Our Shipping Information

Customer Reviews

Be the first to write a review


If your question does not concern this specific product, use our contact form

Have a Question?

Be the first to ask a question about this.

Ask a Question

Customer Reviews

Be the first to write a review