Browse By Collection
Whitfield & Lennox Igniter With Fuse, H8127 Whitfield & Lennox Igniter With Fuse, H8127 Whitfield & Lennox Igniter With Fuse, H8127
Whitfield & Lennox Igniter With Fuse, H8127

Whitfield & Lennox Igniter With Fuse, H8127

$149.99
SKU H8127
MPN H8127

Description

Replacement igniter cartridge for select Whitfield and Lennox pellet stoves.

A new igniter cartridge for Lennox pellet stoves will make lighting your pellet stove fast and easy. This igniter cartridge installs in seconds and comes fully assembled. Our electric heater fuse igniter cartridge easily mounts to your stove allowing the cartridge to protect the igniter from excessive heat and debris. igniter cartridges tend to wear out over time, so it's important to replace it with a quality igniter you can rely on. The igniter cartridge is made from durable materials and guaranteed to provide a perfect fit. You'll be able to light your stove with ease without fumbling with matches or flammable liquids.


Replacement For Part Number s :
  • H8127
  • 12150213
  • 12140213

Compatible Models

    Lennox

  • Montage

    • Whitfield

  • Advantage II-T
  • Advantage II-T C
  • Advantage Plus FS
  • Advantage Plus INS
  • Optima 2 FS
  • Optima 3 FS
  • Profile 20 FS
  • Profile 30 FS
  • Profile 30 Insert
  • Quest Plus FS WP4
  • Quest Plus INS WP4
  • Traditions T300P
  • Traditions TP300
  • Traditions TP340

Video

Instructions

Assembly Instructions For Whitfield & Lennox Igniter With Fuse, H8127

Replacing the H8127, H8127-AMP igniter in a Whitfield or Lennox/ IronStrike Montage pellet stove:


  • Unplug the stove
  • Remove the rear service panel
  • Remove the auger motor from the shaft and remove auger mounting plate
  • On some models and the tools you may be using, the igniter can also be accessed from the left side by removing the room blower
  • Locate the igniter under the hopper, it will have white braided wires
  • Disconnect wires from old igniter and remove the igniter from the stove
  • using a 5/8" wrench, loosen igniter fitting by turning it CCW
  • There will be a red wire with a black cap attached to the igniter wires, this is an inline fuse and must be checked. If the fuse is blown, replace it.
  • Reinstall all items in the reverse order.


Helpful Tips

Replacing the H8127, H8127-AMP igniter in a Whitfield or Lennox/ IronStrike Montage pellet stove:


  • Sometimes the igniter fitting can be very difficult to crack loose, if this is the case, cut the old igniter wires as close to the fitting as possible and use a 5/8" deep-well socket and a breaker bar to crack the fitting loose
  • Always insert the new igniter and hand tighten it by hand to avoid crossing the threads
  • Stoves equipped with an igniter, especially older Whitfields, must have an igniter present in the igniter tube when the stove is operating. If you decide to use the stove without auto ignition for whatever reason, do no operate the stove without an ignition cartridge in the igniter tube, it will not burn properly



It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping!

When Will My Order Ship

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 1PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

How Does Free Shipping Work?

Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Is Expedited Shipping Available?

We offer both overnight and two day air shipping services for all orders placed within the Continental United States. For information on shipping cut-off times, go to our shipping page.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

If you wish to calculate shipping for an item which does not qualify for free shipping, or if you would like the cost to expedite your order, please do the following. Add the item you want to order to your cart and click here to be taken to the cart page where you can enter your country, state / province, and zip code for an estimate.

Shipping Time Estimations

For information on shipping time estimations, see either the Shipping Information & Transit Times on the cart page, or go to our shipping page.

Read More About Our Shipping Information

Please Note: Due to the COVID-19 emergency, USPS and UPS will not guarantee delivery times. Unfortunately, we will not be able to provide a refund for packages shipped which are late. Packages may be delayed 1-2 days. Everyone is trying their best under these circumstance. Thank you for your understanding.

Customer Reviews

Based on 3 reviews
100%
(3)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
B
B.N.
Just used my last igniter
G
G.R.
Plug and Play
S
S.M.
Lennox Ignitor Cart. Heater w/t Fuse. H8127 field

QUESTIONS & ANSWERS

Ask a Question

  • How long does it take for a part to come in to order it

    We have more of this part on order but it is late in the season and we may not get them in right away. We do sell an aftermarket version of this part that is nearly identical in every way.     

Net Orders Checkout

Item Price Qty Total
Subtotal $0.00
Shipping
Total

Shipping Address

Shipping Methods