ComfortBilt Pellet Stove Convection Blower: CB CONVECTION BLOWER-AMP

Replacement universal convection blower for Comfort-Bilt pellet stoves. Please note: this is the blower motor only; the existing frames will need to be reused. Compatible with most ComfortBilt pellet stoves. Comes with hardware and instructions.

Total Length: 14.5"

Air Discharge: 12" x 1.5"

These are all of the confirmed compatible units for this product. Where To Find Your Make & Model

Check these against the part you are replacing before ordering. If a dimension does not match, contact us and we will confirm the fit.

This product is a kit containing 9 total items.

Component Technical Specs

Open a part to see its specifications.

1 xEnviro Empress Free Standing Convection Blower

SKU 50-1455-AMP (opens in new tab)

Quantity In Kit	1
Length (in)	14 ¾"
Width (in)	3 ¾"
Height (in)	3 ¼"
Voltage	115-120
Power type	AC
Wire Connectors	Two Male Spades
Weight	3.50 lbs

1 xHigh-Speed Steel Drill Bit 7/32" Size, 3-3/4"

SKU 8870A125 (opens in new tab)

Quantity In Kit	1
Length (in)	3 ⅞"
Width (in)	⅛"
Height (in)	⅛"
Weight	.5 oz

6 x1/4" Slotted-Hex, #8 x 1/2" Vibration-Resistant Serrated-Flange Piercing Screws

SKU HDW063 (opens in new tab)

Quantity In Kit	6
Length (in)	⅝"
Width (in)	⁵⁄₁₆"
Height (in)	⁵⁄₁₆"
Weight	0.25 oz

1 x12" Wiring adapter for switching a male spade connector into a female spade connector.

SKU FEMALE-TO-FEMALE-12-INCH (opens in new tab)

Quantity In Kit	1
Length (in)	12"
Size	1/4"

Install Instructions For ComfortBilt Pellet Stove Convection Blower: CB CONVECTION BLOWER-AMP

Instructional Documents

• Install Instructions PDF for ComfortBilt Pellet Stove Convection Blower: CB CONVECTION BLOWER-AMP

Instructional Notes

1. Unplug stove

2. Remove rear and side access panels to get to the blower mounting bracket

3. Remove blower from stove by removing the 2 or 4 (depending upon model) 10mm hex bolts that secure the mounting from into the stove.

4. Flip the frame and motor on its side to reveal the 6 rivets binding the blower and frame together. There are 6 rivets. Using the 7/32” drill bit provided, drill off the head of the rivet from the bottom of the mounting frame.

5. After all 6 rivets have been broken free, place something long and rigid under the motor and gently pry the motor away from the frame.

6. Save the gasket as it will be reused.

7. Pre-drill all of the mounting holes in the frame by screwing in a screw. Do all 6 and then back out the screws about 1⁄2 way and then hang your gasket from the protruding screw ends.

8. Starting in the center, align the top hole of the blower frame with the top center hole on the blower and send in the screw until the screw grabs the metal of the blower and starts to pull it down flat. Do this with the remaining screws until each screw is about 80% tight, then fasten all of the screws down tight until the blower is flush against the frame. NOTE: TIGHTENING ANY 1 SCREW BEFORE SETTING ALL OF THE SCREWS INTO THE BLOWER WILL SKEW THE BLOWER, AND HOLES WILL NOT ALIGN. THIS IS WHY WE DO THEM PARTIALLY UNTIL THEY ARE ALL SEATED.

9. The red wire pre-attached to the blower frame is a ground-wire extension. Use this wire to connect your green ground wire which should already be attached somewhere to the stove frame.

This Item Qualifies For Free Shipping!