Quadra-Fire Castile Insert Feed Motor Assembly: SRV414-5400-AMP

This is a complete auger feed motor assembly for the Quadra-Fire Castile Insert made between Jan 2002 and May 2011.

This whole assembly is a compatible fit for Castile Insert, Gen. 1, 2002-2005, and the Castile Insert Gen 2, 2006-2011 when it is installed completely as a whole assembly.

This assembly has updates to the bearing and the motor bracket which ARE NOT COMPATIBLE with older feed assembly parts.

812-4421

This assembly includes the following parts:

• 1 x Feed Motor (812-4421)
• 4 x 8-32 X 3/8'' Phillips Screws (225-0500)
• 1 x 7/8" Lock Collar (229-0520)
• 1 x Nylon Bearing (SRV7000-598)
• 1 x Motor Bracket (7001-039)
• 1 x Feed Motor Gasket (SRV240-0731)
• 1 x Feed Spring Assembly (SRV414-5540)
• 1 x Shaft Set Screw (225-0550) 

This kit uses aftermarket parts where applicable to help you save big!

**NOTES**

• Final bearing height adjustment is required by the installer, instructions included. Download PDF
• This is the correct feed assembly for the CASTILE INSERT made between 2002 - March 2011. All newer models, Castile Insert-B and Castile Insert-C made from 2011 through the current 2021 model use feed assembly 812-4760.

UPC: 652174611706

Replacement For Part Numbers:

• SRV414-5400
• 414-5400

These are all of the confirmed compatible units for this product. This product may fit others, but these are the only ones we suggest ordering it for at this time.

Check these against the part you are replacing before ordering. If a dimension does not match, contact us and we will confirm the fit.

This product is a kit containing 6 total items.

Component Technical Specs

Open a part to see its specifications.

1 xQuadra-Fire 2.4 RPM Auger Feed Motor without Bracket

SKU 812-4421-AMP (opens in new tab)

Quantity In Kit	1
Length (in)	3 ½"
Width (in)	3"
Height (in)	2 ¼"
Voltage	115/120
RPM (Rotations/Minute)	2.4
Rotation Direction	Clockwise
Wire Connector Notes	Includes Optional Adapter Harness
Shaft	1/4"
Weight	1.25 lbs

1 xQuadra-Fire Pellet Stove Nylon Auger Bearing

SKU SRV7000-598 (opens in new tab)

Quantity In Kit	1
Length (in)	1 ⅝"
Width (in)	1 ⅝"
Height (in)	½"
Weight	.25 oz

1 xQuadra-Fire 7/8" Auger Collar with Set Screw

SKU 229-0520 (opens in new tab)

Quantity In Kit	1
Length (in)	1 ½"
Width (in)	1 ½"
Height (in)	½"
Inner Diameter (in)	⅞"
Size	7/8"
Weight	3.00 oz

1 xQuadra-Fire Feed Motor Gasket

SKU SRV240-0731 (opens in new tab)

Quantity In Kit	1
Length (in)	4 ¼"
Width (in)	3"
Height (in)	⅛"
Weight	0.50 oz

1 xQuadra-Fire Castile Insert (Pre-2006) Feed Spring Auger Shaft

SKU SRV414-5540 (opens in new tab)

Quantity In Kit	1
Length (in)	15 ⅞"

1 xFeed Motor Bracket Assembly for the Quadra-Fire Castile Insert Feed Motor Assembly

SKU 7001-039 (opens in new tab)

Quantity In Kit	1

Install Instructions For Quadra-Fire Castile Insert Feed Motor Assembly: SRV414-5400-AMP

Instructional Documents

• Install Instructions PDF for Quadra-Fire SRV414-5400

Instructional Notes

Feed Motor Assembly Instructions for various models PDF

Adjusting the Feed Spring Bearing Height for Various Models PDF

Troubleshooting Notes

The feed system is located behind the firebox and can be removed as an entire assembly. The assembly includes the feed motor, mounting bracket, bearing and feed spring (auger). The hollow feed spring (auger) pulls pellets up the feed tube from the hopper area and drops them down the feed chute into the fire pot at a set rate. The feed motor turns for 7 seconds at each feed interval. The amount of pellets fed into the stove is dictated by the OFF cycle. More pellets = more frequent intervals.

What to check if the unit is NOT feeding pellets:

• Snap Disc #2 malfunctioned
• Vacuum switch is not closing
• Hopper lid switch (if equipped) is not aligned
• Vacuum switch hose is clogged at feed tube
• Capacitor on motor is too close to heat source or is defective
• Bad control box

This Item Qualifies For Free Shipping!