Skip to main content
Skip to main content
Product title:

Quadra-Fire Classic Bay CB1200/1200i Complete Feed Motor Assembly: 812-3690-AMP

Product rating:
Product price:
$249.99

A $150.00 Savings over the OEM

Product SKU ! 812-3690-AMP
Product MPN ! 812-3690
Product availability: In Stock
Bullet point features

Frequently Bought Together

Description

This Quadra-Fire feed motor assembly is used on all model variations of the Classic Bay CB 1200 pellet stove and CB 1200i Pellet Insert

This whole assembly is a compatible fit for all model versions when it is installed completely as a whole assembly.

This assembly has updates to the bearing and the motor bracket which ARE NOT COMPATIBLE with older feed assembly parts.

This assembly includes the following parts:

    • 1 x Feed Motor (812-4421)
    • 4 x 8-32 X 3/8'' Phillips Screws (225-0500)
    • 1 x 7/8" Lock Collar (229-0520)
    • 1 x Nylon Bearing (SRV7000-598)
    • 1 x Motor Bracket (410-7172)
    • 1 x Feed Motor Gasket (SRV240-0731)
    • 1 x Feed Spring Assembly SRV7027-024)
    • 1 x Shaft Set Screw (225-0550)

    **NOTES**

    • Final bearing height adjustment is required by the installer, instructions included. Download PDF


    Replacement For Part Number:

    • 812-3690

    UPC: 652174167449

    Compatible Models

      Quadra-Fire

    • Classic Bay 1200
    • Classic Bay 1200-I

    Technical Specs

    RPM 2.4
    Direction CW
    Amps 1
    Volts 115/120
    Connector 3-PIN Molex

    Videos

    Instructions

    Install Instructions For Quadra-Fire Classic Bay CB1200/1200i Complete Feed Motor Assembly: 812-3690-AMP

    Feed Motor Spring Replacement Instructions


    1. Open the right-side curtain and remove hopper's side heat shield to access wiring and disconnect Molex wire connections. If there are not any Molex wires connectors, then disconnect the spade connectors under feed motor cover.
    2. Remove or support the hopper lid while you work.
    3. Mark the feed adjustment rod position on feed motor cover for future reference. This will eliminate the need to re-set the feed rate when you are done.
    4. Remove the cover and front access plate from hopper. Use a 7 /16" wrench to remove the two nuts holding down the nylon bearing and motor mount.
    5. Remove feed motor / auger assembly by pulling out towards face of the stove.
    6. Install your new assembly.


    NOTE: This assembly has a different bearing and motor mount than what was on previous models. The bracket mounts directly to the feed tube without the nylon block.

    Troubleshooting

    Quadra-Fire Classic Bay 1200 Pellet Stove: Troubleshooting Video: https://youtu.be/ZhgNWi1kE7g


    What to check if the unit is NOT feeding pellets:


    • Snap Disc #2 malfunctioned
    • Vacuum switch is not closing
    • Hopper lid switch (if equipped) is not aligned
    • Vacuum switch hose is clogged at feed tube
    • Capacitor on motor is too close to heat source or is defective
    • Bad control box

    Warranty

    Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

    Shipping Information

    This Item Qualifies For Free Shipping!

    When Will My Order Ship?

    All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

    Do You Offer Express Shipping?

    Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

    How Does Free Shipping Work?

    Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

    Do You Ship To Canada?

    We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

    Do You Ship To Alaska Or Hawaii?

    We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

    Do You Ship Outside The US Or Canada?

    Unfortunately, at this time we do not offer international shipping other than to Canada.

    Shipping Time Estimations

    For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

    Learn More About Our Shipping Information
    Jump back to product information tab navigation

    Description

    This Quadra-Fire feed motor assembly is used on all model variations of the Classic Bay CB 1200 pellet stove and CB 1200i Pellet Insert

    This whole assembly is a compatible fit for all model versions when it is installed completely as a whole assembly.

    This assembly has updates to the bearing and the motor bracket which ARE NOT COMPATIBLE with older feed assembly parts.

    This assembly includes the following parts:

      • 1 x Feed Motor (812-4421)
      • 4 x 8-32 X 3/8'' Phillips Screws (225-0500)
      • 1 x 7/8" Lock Collar (229-0520)
      • 1 x Nylon Bearing (SRV7000-598)
      • 1 x Motor Bracket (410-7172)
      • 1 x Feed Motor Gasket (SRV240-0731)
      • 1 x Feed Spring Assembly SRV7027-024)
      • 1 x Shaft Set Screw (225-0550)

      **NOTES**

      • Final bearing height adjustment is required by the installer, instructions included. Download PDF


      Replacement For Part Number:

      • 812-3690

      UPC: 652174167449

      Technical Specs

      RPM 2.4
      Direction CW
      Amps 1
      Volts 115/120
      Connector 3-PIN Molex

      Instructions

      Assembly Instructions For Quadra-Fire Classic Bay CB1200/1200i Complete Feed Motor Assembly: 812-3690-AMP

      Feed Motor Spring Replacement Instructions


      1. Open the right-side curtain and remove hopper's side heat shield to access wiring and disconnect Molex wire connections. If there are not any Molex wires connectors, then disconnect the spade connectors under feed motor cover.
      2. Remove or support the hopper lid while you work.
      3. Mark the feed adjustment rod position on feed motor cover for future reference. This will eliminate the need to re-set the feed rate when you are done.
      4. Remove the cover and front access plate from hopper. Use a 7 /16" wrench to remove the two nuts holding down the nylon bearing and motor mount.
      5. Remove feed motor / auger assembly by pulling out towards face of the stove.
      6. Install your new assembly.


      NOTE: This assembly has a different bearing and motor mount than what was on previous models. The bracket mounts directly to the feed tube without the nylon block.

      Troubleshooting

      Quadra-Fire Classic Bay 1200 Pellet Stove: Troubleshooting Video: https://youtu.be/ZhgNWi1kE7g


      What to check if the unit is NOT feeding pellets:


      • Snap Disc #2 malfunctioned
      • Vacuum switch is not closing
      • Hopper lid switch (if equipped) is not aligned
      • Vacuum switch hose is clogged at feed tube
      • Capacitor on motor is too close to heat source or is defective
      • Bad control box

      Warranty

      Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

      Shipping Info

      This Item Qualifies For Free Shipping!

      When Will My Order Ship?

      All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

      Do You Offer Express Shipping?

      Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

      How Does Free Shipping Work?

      Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

      Do You Ship To Canada?

      We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

      Do You Ship To Alaska Or Hawaii?

      We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

      Do You Ship Outside The US Or Canada?

      Unfortunately, at this time we do not offer international shipping other than to Canada.

      Shipping Time Estimations

      For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

      Learn More About Our Shipping Information

      Customer Reviews

      Based on 3 reviews
      100%
      (3)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      M
      Mike G.
      Auger complete ass.

      Components went together like factory. I charged the feed tube and the stove works like it should. Parts arrived in three days was great. when I ordered it said 8 to 11 days. I was surprised. I will do business with you again when something fails.

      L
      Lisa S.
      Replaced the motor to our Quadra-Fire nicely

      The local technicians who installed the replacement motor had a little trouble figuring out the wiring because the color codes were different but they got it done. The replacement motor arrived quickly! Thankful that our pellet stove is working again in time for winter.

      T
      Terry h.

      Quadra-Fire Classic Bay CB1200/1200i Complete Feed Motor Assembly, 812-3690-AMP

      QUESTIONS & ANSWERS

      If your question does not concern this specific product, use our contact form

      Have a Question?

      Be the first to ask a question about this.

      Ask a Question

      Customer Reviews

      Based on 3 reviews
      100%
      (3)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      M
      Mike G.
      Auger complete ass.

      Components went together like factory. I charged the feed tube and the stove works like it should. Parts arrived in three days was great. when I ordered it said 8 to 11 days. I was surprised. I will do business with you again when something fails.

      L
      Lisa S.
      Replaced the motor to our Quadra-Fire nicely

      The local technicians who installed the replacement motor had a little trouble figuring out the wiring because the color codes were different but they got it done. The replacement motor arrived quickly! Thankful that our pellet stove is working again in time for winter.

      T
      Terry h.

      Quadra-Fire Classic Bay CB1200/1200i Complete Feed Motor Assembly, 812-3690-AMP