Harman Absolute 43 Front Igniter Bracket: 1-00-777815

Harman Pellet Stove Front Igniter Bracket for the Absolute 43.  This bracket helps to hold the ignitor inside the igniter cradle.  If this bracket is damaged or not seated correctly it can adversely affect how the stove ignites and burns.

Originally Fit Units: Manufacturing date: March 2015 to April 2018.

*Several changes were made to the burn pot on the Absolute 43.  It is important to visually inspect your burn pot to make sure you are purchasing the appropriate part.*

   

The Harman Absolute 43 has a new burnpot upgrade that solves problems with slow or faulty ignition, part 1-00-777901R

This plate is also sold in a kit with new burnpot bolts and the igniter for replacement in an older style Absolute43 Burnpot., 1-00-777200

Replacement For Part Number:

• 1-00-777815

View Compatible Models

UPC: 652174733583

Install Instructions For Harman Absolute 43 Front Igniter Bracket: 1-00-777815

Replacing the igniter on the Absolute43 with a pre2017 burnpot: Click Here to Download the PDF Instructions

1. Disconnect Power
2. Remove the ash pan
3. Remove the Swing Plate. Figure 1.
4. Open the bottom of the burnpot by swinging the clean-out cover to the left, remove any debris that has developed. Figure 2.
5. Remove the two 1/4-20” allan head bolts on the outer front corners of the burnpot using the 3/16” allen wrench supplied with the stove hardware pack in the unit (came with the stove), then remove the burnpot grate by pulling forward. Figure 3.
6. Remove the left rear motor cover located below the hopper and locate the sky blue and yellow wires that go to the igniter through the rear of the feeder. Cut away any cable ties to release the extra loop of wire so the wire can be drawn into the feeder when the igniter is removed from the burnpot.
7. Remove the front igniter cover by bending the metal tab on the left forward from the burnpot grate. With the tab bent out, the cover should lift up off the main bracket hooks. (Note how the wires from the igniter loop toward the front of the burnpot before routing toward the rear of feeder when the igniter is in place.) The igniter will pull straight out of the main bracket. Figure 4.
8. Pull the igniter wires forward through the feeder body until the male/female connectors are out enough to disconnect the old igniter.
9. Connect new igniter and pull the connectors back through the feeder body pulling on the wire from the rear of the unit while making sure the connectors don’t get caught on the burnpot. (Note: Make sure the small weld on the end of the igniter core opposite the wire end is facing front to allow the igniter to fully slide back into the igniter bracket.)
10. With the igniter fully seated into the igniter bracket, re-install the front igniter cover over the hooks of the main igniter bracket, bend tab away from you to keep it securely in place. NOTE: There should be NO WIRES over the lower clean-out hole. It is very important that the wires are pulled to the rear of the feeder body as far a possible.
11. Close and tighten the bottom clean-out cover.
12. Clean the burnpot grate from any debris or buildup and re-install the two 1/4-20” bolts.
13. Replace swing plate making sure the bend is toward the burnpot.
14. Reinstall ash pan.
15. Re-Tie wrap any extra wires in the rear of the unit with tie wraps included in kit.

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

This Item Qualifies For Free Shipping With Orders Over $49!

Learn More About Our Shipping Information