Harman PC45 Pellet Stove Repair and Replacement Parts

Anderol 465 Synthetic Bearing Oil We sell the Anderol synthetic bearing oil for Fasco and other pellet stove blower motors that require oil lubric...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

Harman 3/8" x 10FT Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

Replacement Burn Pot and Tailpipe Gasket for Harman Stoves. This item contains one gasket for the exhaust tailpipe and one gasket for the burnpot. ...

This control board is compatible with all listed compatible models made prior to their updated version with touchscreens on the hopper lid. Include...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

Replacement distribution (convection) blower for Harman Pellet Stoves that use Part# 3-21-33647. This blower is mounted without a gasket in all app...

Replacement blower mounting screw for Harman stoves. These studs are used to attach the combustion blower to the blower mount. Three (3) of these s...

Replacement Harman Black Exhaust Sensing Probe (ESP) for select pellet stoves. A 3 blink error code means that the control board has not detected t...

Harman Burn Pot Scraper for Harman Pellet Stoves, 2-00-773850 This burn pot scraper is used to scrape the ash and creosote from the Harman burn pot...

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units ...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

This knob and post set is compatible with all Harman pellet stoves, boilers, and furnaces that do not have a touchscreen controller. Every applicat...

This is a set of 6 serrated hex nuts that are used to secure the combustion / exhaust blower motor onto blower housings that have threaded mounting...

Harman Pellet Stove Burn Pot Gasket. Part: 1-00-07381. (Burn Pot Gasket Only). The burn pot gasket fits between the burn pot and the body of the st...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sy...

Replacement Tailpipe Gasket for Harman Stoves. This is the gasket that seals the stove to the appliance collar (tailpipe) that connects to the vent...

This is a flat braided gasket that is 1/4" wide and 7.5' long with an adhesive backing. Harman uses this gasket to create an air seal between the d...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

Ceramic plate overfire replacement gasket for Harman pellet stoves, inserts, and boilers that utilize a burn pot with primary air inlets that over ...

This 6 Amp, 30mm, control board fuse is located on the backside of your Harman Stove Circuit board. Most controllers, Revisions A-D, which were use...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sys...

This bearing is part of the Harman feed system. It goes on the armature that turns the auger.

This 4 RPM auger feed motor has a clockwise rotation (CW) as viewed from the shaft side. This motor is used ONLY used in direct drive applications...

Set of four screws and clips for securing the door glass into the following units: Accentra Insert, Accentra, 52i, P35i, P38, P43, P61, P61A, P68, ...

Replacement Grommet & Spacer for many Harman models. It is used on certain auger motors. This part needs to be replaced when the rubber becomes...

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

Replacement Harman Black Exhaust Sensing Probe (ESP) for select pellet stoves. A 3 blink error code means that the control board has not detected t...

This is the auger shaft assembly that moves the pellets from the hopper to the burnpot. We get a lot of people ordering the wrong shaft so please ...

This latch expands when latched down to hold the hopper lid closed while making an air-tight seal. Used on many pellet stoves, coal stokers, furnac...

This is a Harman Auger Extension (agitator) for use with the PC45 multi-fuel (pellet/ corn) burn pot. It's time to replace this part when the metal...

This is a flat braided gasket that is 1/4" wide and 15' long with an adhesive backing. Harman uses this gasket to create an air seal between the do...

Harman Distribution Blower for many units, see our stove compatibility tab. The distribution blower is also known as the room air blower or convect...

This 5" combustion blower fan blade is a single-sided impeller used on the Harman Accentra-Cast, Invincible Insert, and the PC45. If any of the pet...

This is a 1/4" female spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical component...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

This 4 RPM auger feed motor has a clockwise rotation (CW) as viewed from the shaft side. This motor is used ONLY used in direct drive applications...

This 4 RPM auger feed motor has a clockwise rotation (CW) as viewed from the shaft side. This motor is used ONLY used in direct drive applications ...

Harman 450 Watt Igniter for units with pressurized ignition, to include: PC45, HF60, PF100, and PB1050. This part was formerly known as 3-20-00450.  

This firebrick measures 9" x 4-1/2" x 1-1/4" and is sold individually (just 1 brick). Fire Bricks are essential to the overall performance of your ...

This is a 1/4" male spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical components ...

This Wooden Handle(with bolt) is for the following stove models: Accentra Insert, Accentra, Accentra 52i  P35i,P43,P61,P61A, PC45 P38 (post serial...

Stove Bright brand High Temperature Paint. Rated to 1200 degrees. Satin black has a higher sheen finish than traditional flat blacks or metallic bl...

Harman 5" Single Paddle Impeller This stove part fits many Harman stove models. See the "Compatible Stoves" tab for details The Harman Combustion/E...

Replacement Pyroceramic Glass for Harman P38, P43, PC45, and P61 Pellet Stoves and Magnum 44 Coal Stoker. Measures 9 1/2" high x 13 5/16" wide, wit...

This is the auger shaft assembly that moves the pellets from the hopper to the burnpot. We get a lot of people ordering the wrong shaft so please r...

This decorative 3-log set replaces the clay fire brick inside the firebox of P Series freestanding pellet stoves. The logs are used in place of the...