Harman P35i Pellet Stove Repair and Replacement Parts

Anderol 465 Synthetic Bearing Oil We sell the Anderol synthetic bearing oil for Fasco and other pellet stove blower motors that require oil lubric...

This 306 Watt igniter is compatible with all automatic ignition Harman except those which use a pressurized ignition system. Note: This igniter w...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

Replacement Burn Pot and Tailpipe Gasket for Harman Stoves. This item contains one gasket for the exhaust tailpipe and one gasket for the burnpot. ...

This 306 Watt igniter is compatible with all automatic ignition Harman stoves. Was formally a 15 Fin..works with all Harman models listed. View our...

This control board is compatible with all listed compatible models made prior to their updated version with touchscreens on the hopper lid. The Con...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

This flame guide replacement part is compatible with the following Harman stoves: -Accentra Insert, XXV, P35i, P43, P68, HF60, 52i, P43, Absolute43...

Replacement Harman Dual Side Distribution Blower made by Fasco. The distribution blower, also referred to as the convection or room air blower, blo...

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units ...

Replacement blower mounting screw for Harman stoves. These studs are used to attach the combustion blower to the blower mount. Three (3) of these s...

Harman Burn Pot Scraper for Harman Pellet Stoves, 2-00-773850 This burn pot scraper is used to scrape the ash and creosote from the Harman burn pot...

This knob and post set is compatible with all Harman pellet stoves, boilers, and furnaces that do not have a touchscreen controller. Every applicat...

Replacement Flame Guide for Harman Stoves. Measurements: 6-1/4" to 3-1/2" x 4-1/8. Replaces Old Harman part number 3-00-674069. The flame guide is...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

Replacement silicone docking gasket for all Harman pellet stove inserts. Older versions of this gasket were red in color, this is the replacement f...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sy...

This 4 3/4" combustion blower fan blade is the single-sided impeller that is used on the Harman Accentra Insert, P35i and P35i-C Insert, and the PF...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

This 6 Amp, 30mm, control board fuse is located on the backside of your Harman Stove Circuit board. Most controllers, Revisions A-D, which were use...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sys...

Harman Burn Pot Gasket, 1-00-07381 (Burn Pot Gasket Only) The burn pot gasket goes between the burn pot and the body of the stove and prevents comb...

Replacement Grommet & Spacer for many Harman models. It is used on certain auger motors. This part needs to be replaced when the rubber becomes...

This Harman Pellet Stove Hopper Lid Gasket is compatible with all Harman stoves and inserts that have a glass hopper lid and the 60 Series HHT Boil...

Replacement 1/4-20 X 5/8 thumb screw / wingscrew for Harman stoves. Used on most pellet stoves to hold the cleanout cover on the burnpot. Each stov...

This bearing is part of the Harman feed system. It goes on the armature that turns the auger.

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units...

This is a flat braided gasket that is 1/4" wide and 7.5' long with an adhesive backing. Harman uses this gasket to create an air seal between the d...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

This decorative ceramic log is an optional item often sold with the purchase of a new stove or insert but is not required to operate the stove.

This 4 RPM auger feed motor has a clockwise rotation (CW) as viewed from the shaft side. This motor is used ONLY used in direct drive applications...

This 4 RPM auger feed motor has a clockwise rotation (CW) as viewed from the shaft side. This motor is used ONLY used in direct drive applications ...

Harman Distribution Blower for the XXV, P35i & Accentra-Cast, 1-00-29145. There have been many revisions to this motor over the years. This ver...

This is a set of 6 serrated hex nuts that are used to secure the combustion / exhaust blower motor onto blower housings that have threaded mounting...

This 4 3/4" combustion blower fan blade is the single-sided impeller that is used on the Harman Accentra Insert, P35i and P35i-C Insert, and the PF...

This is a flat braided gasket that is 1/4" wide and 15' long with an adhesive backing. Harman uses this gasket to create an air seal between the do...