Harman Accentra Cast Free Standing Pellet Stove Repair and Replacement Parts

Anderol 465 Synthetic Bearing Oil We sell the Anderol synthetic bearing oil for Fasco and other pellet stove blower motors that require oil lubric...

Harman 306 Watt Igniter.  Compatible with most automatic ignition Harman units. The ignitor works by super heating the air that passes through the ...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

Harman 3/8" x 10FT Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

Replacement Burn Pot and Tailpipe Gasket for Harman Stoves. This item contains one gasket for the exhaust tailpipe and one gasket for the burnpot. ...

This control board is compatible with all listed compatible models made prior to their updated version with touchscreens on the hopper lid. Include...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

Harman 306 Watt igniter.  Compatible with most automatic ignition Harman units *(Not compatible with units using the pressurized ignition system)* ...

Harman Pellet Stove Flame Guide. The flame guide helps to protect your stove by acting as a buffer between the flame and rear panel of the unit. Th...

Replacement Harman Dual Side Distribution Blower made by Fasco. The distribution blower, also referred to as the convection or room air blower, blo...

Replacement blower mounting screw for Harman stoves. These studs are used to attach the combustion blower to the blower mount. Three (3) of these s...

Harman Pellet Stove OEM Flame Guide. The flame guide helps to protect your stove by acting as a buffer between the flame and interior of the unit. ...

Replacement Harman Black Exhaust Sensing Probe (ESP) for select pellet stoves. A 3 blink error code means that the control board has not detected t...

Harman Burn Pot Scraper for Harman Pellet Stoves, 2-00-773850 This burn pot scraper is used to scrape the ash and creosote from the Harman burn pot...

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units ...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

This knob and post set is compatible with all Harman pellet stoves, boilers, and furnaces that do not have a touchscreen controller. Every applicat...

Harman Pellet Stove Burn Pot Gasket. Part: 1-00-07381. (Burn Pot Gasket Only). The burn pot gasket fits between the burn pot and the body of the st...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sy...

Harman Pellet Stove Igniter & Cradle Kit.  This kit contains the most recently designed ignitor and cradle from Harman.  This cradle & igni...

Replacement Tailpipe Gasket for Harman Stoves. This is the gasket that seals the stove to the appliance collar (tailpipe) that connects to the vent...

This is a flat braided gasket that is 1/4" wide and 7.5' long with an adhesive backing. Harman uses this gasket to create an air seal between the d...

One Replacement 1/4" screw post with washer. These are the screws that attach the glass hopper lid to the hinges. If you can hear a "whistle" from ...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

This 6 Amp, 30mm, control board fuse is located on the backside of your Harman Stove Circuit board. Most controllers, Revisions A-D, which were use...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sys...

This bearing is part of the Harman feed system. It goes on the armature that turns the auger.

This Harman Pellet Stove Hopper Lid Gasket is compatible with all Harman stoves and inserts that have a glass hopper lid and the 60 Series HHT Boil...

Replacement Grommet & Spacer for many Harman models. It is used on certain auger motors. This part needs to be replaced when the rubber becomes...

Replacement 1/4-20 X 5/8 thumb screw / wingscrew for Harman stoves. Used on most pellet stoves to hold the cleanout cover on the burnpot. Each stov...

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units...

Harman Pellet Stove Ignitor & Updated Cradle. This is the most recent design from Harman.  This cradle can be used anywhere a finned igniter is...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

Replacement Harman Black Exhaust Sensing Probe (ESP) for select pellet stoves. A 3 blink error code means that the control board has not detected t...

This is the auger shaft assembly that moves the pellets from the hopper to the burnpot. We get a lot of people ordering the wrong shaft so please ...

This "counter-clock-wise" 4 RPM Auger Feed Motor is used on the Accentra-Cast, Advance, and the XXV pellet stoves that have the indirect chain driv...

This is a flat braided gasket that is 1/4" wide and 15' long with an adhesive backing. Harman uses this gasket to create an air seal between the do...

This 5" combustion blower fan blade is a single-sided impeller used on the Harman Accentra-Cast, Invincible Insert, and the PC45. If any of the pet...

This "counter-clock-wise" 4 RPM Auger Feed Motor is used on the Accentra-Cast, Advance, and the XXV pellet stoves that have the indirect chain driv...

This is a 1/4" female spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical component...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

The indirect feed system was used on the Harman Accentra-Cast, Advance, and the XXV prior to 2009.  Models with the indirect system are: Accentr...

Harman Distribution Blower for the XXV, P35i & Accentra-Cast, 1-00-29145. There have been many revisions to this motor over the years. This ver...

This "counter-clock-wise" 4 RPM Auger Feed Motor is used on the Accentra-Cast, Advance, and XXV pellet stoves that have the indirect chain drive fe...

This kit contains all the shared common replacement parts for all Harman pellet stoves and inserts which utilize the 1-00-05886 control board. See ...

This is the 3/4" nylon feeder tensioner used to keep the chain in alignment on the freestanding Advance, XXV, and Accentra pellet stoves with a 'C...

This glass hopper lid id designed to fit both the Accentra-Cast and the XXV models prior to the introduction of touchscreen controllers. Hardware a...

This is a 1/4" male spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical components ...