Harman PB105 Pellet Boiler Repair and Replacement Parts

Harman 306 Watt Igniter.  Compatible with most automatic ignition Harman units. The ignitor works by super heating the air that passes through the ...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

This 5" combustion blower fan blade is a double-sided impeller that is used on most freestanding Harman Pellet Stoves. Check out the compatible sto...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

This 5" combustion blower fan blade is a double-sided impeller that is used on most freestanding Harman Pellet Stoves. Includes a set screw for mou...

Harman 306 Watt igniter.  Compatible with most automatic ignition Harman units *(Not compatible with units using the pressurized ignition system)* ...

Harman Pellet Stove Flame Guide. The flame guide helps to protect your stove by acting as a buffer between the flame and rear panel of the unit. Th...

Replacement blower mounting screw for Harman stoves. These studs are used to attach the combustion blower to the blower mount. Three (3) of these s...

Harman Pellet Stove OEM Flame Guide. The flame guide helps to protect your stove by acting as a buffer between the flame and interior of the unit. ...

Replacement Harman Black Exhaust Sensing Probe (ESP) for select pellet stoves. A 3 blink error code means that the control board has not detected t...

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units ...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

This knob and post set is compatible with all Harman pellet stoves, boilers, and furnaces that do not have a touchscreen controller. Every applicat...

Harman Pellet Stove Burn Pot Gasket. Part: 1-00-07381. (Burn Pot Gasket Only). The burn pot gasket fits between the burn pot and the body of the st...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sy...

Replacement Tailpipe Gasket for Harman Stoves. This is the gasket that seals the stove to the appliance collar (tailpipe) that connects to the vent...

This is a flat braided gasket that is 1/4" wide and 7.5' long with an adhesive backing. Harman uses this gasket to create an air seal between the d...

Ceramic plate overfire replacement gasket for Harman pellet stoves, inserts, and boilers that utilize a burn pot with primary air inlets that over ...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sys...

This bearing is part of the Harman feed system. It goes on the armature that turns the auger.

Replacement 1/4-20 X 5/8 thumb screw / wingscrew for Harman stoves. Used on most pellet stoves to hold the cleanout cover on the burnpot. Each stov...

Harman Pellet Stove Ignitor & Updated Cradle. This is the most recent design from Harman.  This cradle can be used anywhere a finned igniter is...

Replacement Harman Black Exhaust Sensing Probe (ESP) for select pellet stoves. A 3 blink error code means that the control board has not detected t...

This latch expands when latched down to hold the hopper lid closed while making an air-tight seal. Used on many pellet stoves, coal stokers, furnac...

This is a flat braided gasket that is 1/4" wide and 15' long with an adhesive backing. Harman uses this gasket to create an air seal between the do...

This is a 1/4" female spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical component...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

This 1" flat gasket is used for the following applications: Invincible and Accentra Inserts - mounted on the rack rails to reduce friction when s...

Harman 450 Watt Igniter for units with pressurized ignition, to include: PC45, HF60, PF100, and PB1050. This part was formerly known as 3-20-00450.  

This is a 1/4" male spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical components ...

Please read this section and compare against your stove's serial number to be sure you are getting the correct part!    Some models had more than ...

Replacement Pyroceramic Glass for Harman P38, P43, PC45, and P61 Pellet Stoves and Magnum 44 Coal Stoker. Measures 9 1/2" high x 13 5/16" wide, wit...

This 6RPM clockwise (CW) auger feed motor is used on all Harman pellet furnaces and boilers and was adopted for use on the P68 pellet stove in 200...

 Harman Pellet Stove Burn Pot Clean Out Cover.  This cover plate is located on the underside of the burn pot.  Removing this cover will give you ac...

This is a replacement wiring adapter for switching a male spade connector into a female spade connector. Can be used on blowers, auger motors, and ...

Replacement hopper lid gasket for Harman Pellet and Coal Stoves. Measures 5 feet long with self-adhesive backing. This is also the gasket you want ...

This is a replacement wiring adapter for switching a female spade connector into a male spade connector. Can be used on blowers, auger motors and m...

This 6RPM clockwise (CW) auger feed motor is used on all Harman pellet furnaces and boilers and was adopted for use on the P68 pellet stove in 2009...

Harman Air Intake Gasket for pellet most models. This is used to seal the intake flapper to the air intake weldment.

Harman Room Sensor Probe Extension 14FT, 3-20-674101 This sensor can be used with Harman pellet stoves and inserts to lengthen the distance of the ...

Harman Replacement Hose For The Differential Pressure Sensor Switch Approximately 15"

This is the auger shaft assembly that moves the pellets from the hopper to the burnpot. We get a lot of people ordering the wrong shaft so please r...

This retainer is used to secure the bearing of the auger shaft assembly to the feeder body weldment. Use on all Harman pellet burning stoves, inser...

Feeder air crossover tube kit for Harman pellet stove and inserts. Kit Includes: 8-1/2" of 9mm silicone tube Two (2) 3/8" brass sleeves, and instr...

Cleanup the ashes from your stove is a breeze with the new AV15E ash vacuum from US Stove Company. With a 2.5 peak horse power motor and a 6.5 Gall...

Replacement Black 5/16” Hex Head Common Screw for Harman Pellet Stoves; used to hold the service panels, ignition cradle, and more, compatible with...

Replacement 5 amp fuse for Harman Pellet Stoves. Fits many models. If you have an XXV, please check the date on your manufacturer's tag. This part ...

Harman Adjustable Igniter Cradle (Updated).  This cradle can be used on any units using finned igniters and is backward-compatible with all auto-ig...