Harman HF60 Pellet Boiler Repair and Replacement Parts

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

This 5" combustion blower fan blade is a double-sided impeller that is used on most freestanding Harman Pellet Stoves. Check out the compatible sto...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

This 5" combustion blower fan blade is a double-sided impeller that is used on most freestanding Harman Pellet Stoves. Check out the compatible sto...

This flame guide replacement part is compatible with the following Harman stoves: -Accentra Insert, XXV, P35i, P43, P68, HF60, 52i, P43, Absolute43...

This knob and post set is compatible with all Harman pellet stoves, boilers, and furnaces that do not have a touchscreen controller. Every applicat...

Replacement Flame Guide for Harman Stoves. Measurements: 6-1/4" to 3-1/2" x 4-1/8. Replaces Old Harman part number 3-00-674069. The flame guide is...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sy...

Replacement blower mounting screw for Harman and Heatilator Eco Choice stoves. These studs are used to attach the combustion blower to the blower m...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sys...

This bearing is part of the Harman feed system. It goes on the armature that turns the auger.

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

Replacement Tailpipe Gasket for Harman Stoves. This is the gasket that seals the stove to the appliance collar (tailpipe) that connects to the vent...

This Harman Pellet Stove Hopper Lid Gasket is compatible with all Harman stoves and inserts that have a glass hopper lid and the 60 Series HHT Boil...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

Ceramic plate overfire replacement gasket for Harman pellet stoves, inserts, and boilers that utilize a burn pot with primary air inlets that over ...

Harman 450 Watt Igniter for units with pressurized ignition, to include: PC45, HF60, PF100, and PB1050. This part was formerly known as 3-20-00450.  

This latch expands when latched down to hold the hopper lid closed while making an air-tight seal. Used on many pellet stoves, coal stokers, furnac...

This is the auger shaft assembly that moves the pellets from the hopper to the burnpot. We get a lot of people ordering the wrong shaft so please r...

This 6RPM clockwise (CW) auger feed motor is used on all Harman pellet furnaces and boilers and was adopted for use on the P68 pellet stove in 2009...

This 6RPM clockwise (CW) auger feed motor is used on all Harman pellet furnaces and boilers and was adopted for use on the P68 pellet stove in 200...

Harman Air Intake Gasket for pellet most models. This is used to seal the intake flapper to the air intake weldment.

This is the auger shaft assembly that moves the pellets from the hopper to the burnpot. We get a lot of people ordering the wrong shaft so please ...

This burn pot cleanout cover with 2 wingscrews is located at the front of all Harman pellet stoves and pellet inserts that are equipped with automa...

Harman Room Sensor Probe Extension 14FT, 3-20-674101 This sensor can be used with Harman pellet stoves and inserts to lengthen the distance of the ...

Harman 450 Watt Ignitor, 1-00-10450 This Ignitor is used for some Harman Furnaces, Boilers, and pellet stoves. (see compatible units tab)  This par...

Feeder air crossover tube kit for Harman pellet stove and inserts and Heatilator Eco Choice pellet boilers. Kit Includes: 8-1/2" of 9mm silicone t...

Replacement 8' power cord with ends for Harman and Heatilator Eco Choice pellet stoves. Note: This part and part 3-20-29685 are the same. The only ...

Control board for both Harman PB105, HF60, and Eco-Choice BA105 Pellet Boilers. Comes with knobs, posts, and installation instructions.    

Replacement 1/2 pillow block for Harman and Heatilator Eco Choice stoves.

This is a 1/4" female spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical component...

This 6RPM clockwise (CW) auger feed motor is used on all Harman pellet furnaces and boilers and was adopted for use on the P68 pellet stove in 2009...

Diagnostic Display Module for Harman Pellet Stoves without TC Controllers. Accentra FS, Accentra Insert, XXV, P68, P61A, P43, P38+, P38, P35i, PC45...

This is a 1/4" male spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical components ...

Replacement hopper lid gasket for Harman Pellet and Coal Stoves and Heatilator Furnaces and Boilers.  Measures 5 feet long with self-adhesive backi...

This replacement feed plate assembly is designed for all pellet stoves and inserts post-2009 that use the UL Feeder Body. Feeder body weldments mad...

This retainer is used to secure the bearing of the auger shaft assembly to the feeder body weldment. Use on all Harman pellet burning stoves, inser...

Replacement auger motor fan blade for 6RPM Auger Feed Motor 3-20-09302. It Fits HF60, P68, and PF100 models made after 2008. This fan blade is not ...

This is a replacement wiring adapter for switching a female spade connector into a male spade connector. Can be used on blowers, auger motors and m...

Replacement UL Feeder Cam Block for Harman Pellet Stoves.  Accentra Cast - beginning serial number: 008400001 Advance - beginning serial number...

Harman Auger Motor Mount Bracket with Grommet for use on UL feeder body weldments. Models with preceding serial numbers use the motor bracket, 1-00...

Replacement Black 5/16” Hex Head Common Screw for Harman Pellet Stoves; used to hold the service panels, ignition cradle, and more, compatible with...