Harman P68-C Pellet Stove Repair and Replacement Parts

Harman 306 Watt Igniter.  Compatible with most automatic ignition Harman units. The ignitor works by super heating the air that passes through the ...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

Harman 3/8" x 10FT Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

This 5" combustion blower fan blade is a double-sided impeller that is used on most freestanding Harman Pellet Stoves. Check out the compatible sto...

Replacement Burn Pot and Tailpipe Gasket for Harman Stoves. This item contains one gasket for the exhaust tailpipe and one gasket for the burnpot. ...

This control board is compatible with all listed compatible models made prior to their updated version with touchscreens on the hopper lid. Include...

This exhaust blower motor is extremely durable and is used on most steel and cast iron Harman pellet stoves.  Some pellet stoves had an older versi...

This 5" combustion blower fan blade is a double-sided impeller that is used on most freestanding Harman Pellet Stoves. Includes a set screw for mou...

Harman Pellet Stove Flame Guide (Measurements: 7" x 3-3/4" x 4"). The flame guide helps to protect your stove by acting as a buffer between the fla...

Harman 306 Watt igniter.  Compatible with most automatic ignition Harman units *(Not compatible with units using the pressurized ignition system)* ...

Replacement distribution (convection) blower for Harman Pellet Stoves that use Part# 3-21-33647. This blower is mounted without a gasket in all app...

Replacement blower mounting screw for Harman stoves. These studs are used to attach the combustion blower to the blower mount. Three (3) of these s...

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units ...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

This knob and post set is compatible with all Harman pellet stoves, boilers, and furnaces that do not have a touchscreen controller. Every applicat...

This is a set of 6 serrated hex nuts that are used to secure the combustion / exhaust blower motor onto blower housings that have threaded mounting...

Harman Pellet Stove Burn Pot Gasket. Part: 1-00-07381. (Burn Pot Gasket Only). The burn pot gasket fits between the burn pot and the body of the st...

Harman Pellet Stove Flame Guide (Measurements:  7" x 3-3/4" x 4"). The flame guide helps to protect your stove by acting as a buffer between the fl...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sy...

Harman Pellet Stove Igniter & Cradle Kit.  This kit contains the most recently designed ignitor and cradle from Harman.  This cradle & igni...

Replacement Tailpipe Gasket for Harman Stoves. This is the gasket that seals the stove to the appliance collar (tailpipe) that connects to the vent...

This is a flat braided gasket that is 1/4" wide and 7.5' long with an adhesive backing. Harman uses this gasket to create an air seal between the d...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

Ceramic plate overfire replacement gasket for Harman pellet stoves, inserts, and boilers that utilize a burn pot with primary air inlets that over ...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sys...

This bearing is part of the Harman feed system. It goes on the armature that turns the auger.

Set of four screws and clips for securing the door glass into the following units: Accentra Insert, Accentra, 52i, P35i, P38, P43, P61, P61A, P68, ...

Replacement Grommet & Spacer for many Harman models. It is used on certain auger motors. This part needs to be replaced when the rubber becomes...

Replacement 1/4-20 X 5/8 thumb screw / wingscrew for Harman stoves. Used on most pellet stoves to hold the cleanout cover on the burnpot. Each stov...

This room-temperature sensor is required by all Harman pellet stoves and inserts to use the "Room Temp" or "Automatic" mode setting on older units...

Harman Pellet Stove Ignitor & Updated Cradle. This is the most recent design from Harman.  This cradle can be used anywhere a finned igniter is...

Harman 3/8" Replacement Pellet Stove and Wood Stove Door Rope & Ash Pan Gasket. See our compatible stoves tab for compatibility.

This latch expands when latched down to hold the hopper lid closed while making an air-tight seal. Used on many pellet stoves, coal stokers, furnac...

This is a flat braided gasket that is 1/4" wide and 15' long with an adhesive backing. Harman uses this gasket to create an air seal between the do...

Harman Distribution Blower for many units, see our stove compatibility tab. The distribution blower is also known as the room air blower or convect...

This is a 1/4" female spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical component...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

This kit contains all the shared common replacement parts for all Harman pellet stoves and inserts which utilize the 1-00-05886 control board. See ...

This firebrick measures 9" x 4-1/2" x 1-1/4" and is sold individually (just 1 brick). Fire Bricks are essential to the overall performance of your ...

This is a 1/4" male spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical components ...

This Wooden Handle(with bolt) is for the following stove models: Accentra Insert, Accentra, Accentra 52i  P35i,P43,P61,P61A, PC45 P38 (post serial...

Please read this section and compare against your stove's serial number to be sure you are getting the correct part!    Some models had more than ...

This decorative 3-log set replaces the clay fire brick inside the firebox of P Series freestanding pellet stoves. The logs are used in place of the...

This 6RPM clockwise (CW) auger feed motor is used on all Harman pellet furnaces and boilers and was adopted for use on the P68 pellet stove in 200...

**THIS GLASS IS CLEAR AND DOES NOT HAVE A MIRRORED FINISH** Replacement Glass for Harman P68 and P35i Series pellet stoves and inserts. This glass ...

This 5 Amp, 20mm control board fuse is located on the backside of your Harman Stove Circuit board. All units made after 2013, with controllers Revi...

 Harman Pellet Stove Burn Pot Clean Out Cover.  This cover plate is located on the underside of the burn pot.  Removing this cover will give you ac...

This is a replacement wiring adapter for switching a male spade connector into a female spade connector. Can be used on blowers, auger motors, and ...