Harman Allure 50 Pellet Stove Repair and Replacement Parts

This 306 Watt igniter is compatible with all automatic ignition Harman stoves except the PC45 and the PB105, which use a pressurized ignition syste...

Anderol 465 Synthetic Bearing Oil We sell the Anderol synthetic bearing oil for Fasco and other pellet stove blower motors that require oil lubric...

Replacement Burn Pot and Tailpipe Gasket for Harman Stoves. This item contains one gasket for the exhaust tailpipe and one gasket for the burnpot. ...

This 306 Watt igniter is compatible with all automatic ignition Harman stoves. Was formally a 15 Fin..works with all Harman models listed. View our...

Replacement distribution (convection) blower for Harman Pellet Stoves that use Part# 3-21-33647. This blower is mounted without a gasket in all app...

Harman Burn Pot Scraper for Harman Pellet Stoves, 2-00-773850 This burn pot scraper is used to scrape the ash and creosote from the Harman burn pot...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sy...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

One Replacement 1/4" screw post with washer. These are the screws that attach the glass hopper lid to the hinges. If you can hear a "whistle" from ...

A pressure switch is often referred to as a vacuum switch. This sensor is looking for airflow within the stove to close the circuit to the feed sys...

Harman Burn Pot Gasket, 1-00-07381 (Burn Pot Gasket Only) The burn pot gasket goes between the burn pot and the body of the stove and prevents comb...

This bearing is part of the Harman feed system. It goes on the armature that turns the auger.

Harman Advance, Allure 50 & Absolute 63 Flame Guide, 3-00-06644 This is the replacement flame guide for the specific Harman Pellet Stoves. This...

This version of the ESP is the correct part for any model made after 2008. This updated ESP has red wires, as opposed to the previous probes which ...

Replacement Tailpipe Gasket for Harman Stoves. This is the gasket that seals the stove to the appliance collar (tailpipe) that connects to the vent...

This Harman Pellet Stove Hopper Lid Gasket is compatible with all Harman stoves and inserts that have a glass hopper lid and the 60 Series HHT Boil...

Replacement 1/4-20 X 5/8 thumb screw / wingscrew for Harman and Heatilator Eco Choice stoves. Used on most pellet stoves to hold the cleanout cover...

Harman Distribution Blower for many units, see our stove compatibility tab. The distribution blower is also known as the room air blower or convect...

This is a flat braided gasket that is 1/4" wide and 7.5' long with an adhesive backing. Harman uses this gasket to create an air seal between the d...

This is a flat braided gasket that is 1/4" wide and 15' long with an adhesive backing. Harman uses this gasket to create an air seal between the do...

Harman Advance, Allure 50 & Absolute 63 Flame Guide, 3-00-06644 This is the replacement flame guide for the specific Harman Pellet Stove. This ...

HARMAN WIRELESS ROOM SENSOR THERMOSTAT Fits Models:  Absolute43, Absolute63, Allure50, XXV-TC, and Accentra Insert 52i-TC Harman Wireless Room Sens...

This is an outboard 4RPM Auger Feed Motor for the Harman Advance, Accentra & XXV pellet stoves with a direct drive feeder design. These motors ...

This is the auger shaft assembly that moves the pellets from the hopper to the burnpot. We get a lot of people ordering the wrong shaft so please r...

This 5 Amp, 20mm control board fuse is located on the backside of your Harman Stove Circuit board. All units made after 2013, with controllers Revi...

Harman Air Intake Gasket for pellet most models. This is used to seal the intake flapper to the air intake weldment.

This is the gasket that seals the Ultra air intake assembly to the feeder body weldment, for Harman and Heatilator Eco Choice pellet stoves.

This is the auger shaft assembly that moves the pellets from the hopper to the burnpot. We get a lot of people ordering the wrong shaft so please ...

Feeder air crossover tube kit for Harman pellet stove and inserts and Heatilator Eco Choice pellet boilers. Kit Includes: 8-1/2" of 9mm silicone t...

This is an outboard 4RPM Auger Feed Motor for the Harman Advance, Accentra & XXV pellet stoves with a direct drive feeder design. These motors ...

Replacement 3" Flue Tailpipe for all freestanding Harman Pellet Stoves. This appliance collar connects to the venting adapter to connect the stove ...

This is a 1/4" female spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical component...

Replacement 1/2 pillow block for Harman and Heatilator Eco Choice stoves.

This igniter cradle has an adjustable depth and is the most recent design from Harman for their finned ignition system. This cradle can be used any...

This is a 1/4" male spade, fully Insulated "Quick-Disconnect" terminal for 22-18 wire gauge that is used to connect power to electrical components ...

This is the room sensing probe that is attached to the back or side of all Harman pellet stoves and inserts. Its purpose is to read the return air ...

This retainer is used to secure the bearing of the auger shaft assembly to the feeder body weldment. Use on all Harman pellet burning stoves, inser...

This replacement feed plate assembly is designed for all pellet stoves and inserts post-2009 that use the UL Feeder Body. Feeder body weldments mad...

This outside air vent assembly is used as an outside hood and receiver for any 3" aluminum flex liner when using an outside air connection that is ...

This is a replacement wiring adapter for switching a female spade connector into a male spade connector. Can be used on blowers, auger motors and m...

This igniter cradle has an adjustable depth and is the most recent design from Harman for their finned ignition system. This cradle can be used any...

Harman's leveling leg kit contains four legs. Each leg is a threaded post fitted with a rubber foot. These legs install under the stove and allow f...

Replacement Harman TouchPad for all Harman pellet stoves and inserts with the Easy-Touch Touchscreen Controller. See the instructions tab for progr...

This is a replacement wiring adapter for switching a male spade connector into a female spade connector. Can be used on blowers, auger motors, and ...

Replacement Black 5/16” Hex Head Common Screw for Harman Pellet Stoves; used to hold the service panels, ignition cradle, and more, compatible with...