Skip to main content
Skip to main content
Product title:

Harman Distribution Blower: 1-00-29145

Product rating:
Product price:
$399.99
Product SKU ! 1-00-29145
Product MPN ! 1-00-29145
Product availability: In Stock
Bullet point features

Frequently Bought Together

Total Price: $419.98

Description

Harman Convection Blower 1-00-29145. There have been many revisions to this motor over the years. This version of the blower has been in service for quite a while now and is very stable in all compatible units.

 

As technical revisions were made, this blower was also referred to as 3-21-29045, 3-21-29145, and 3-21-39145 which are now obsolete part #'s. Part 1-00-29145 is the most current revision.

When mounting this motor into the Harman Accentra-Cast, this is the pad gasket that sits under the motor, 3-44-247118


Replacement For Part Numbers:

  • 1-00-29145
  • 3-21-29045
  • 3-21-29145
  • 3-21-39145

View Compatible Models

UPC: 652174670741

Compatible Models

    Harman

  • Accentra Cast FS
  • P35i
  • P35i-C
  • XXV
  • XXV TC

Technical Specs

Wiring Connectors 2 or 3 Female
Tools Required 5/16" socket Phillips Screwdriver #2 | Accentra FS also requires 3/8" socket with extension
Volts 120V
RPM 1500 RPM
Cycles 60 HZ
Amps 1.17 AMPS
Blower Dimensions 19"W X 3-1/2"H X 4-1/4" D
Mount Holes on Center 18-1/2" W X 1" D
Mounting Plate Overall 19-1/8"W x 2-1/8" D

Videos

Instructions

Install Instructions For Harman Distribution Blower: 1-00-29145

XXV/ Accentra-Cast units made without a rocker switch will ONLY have wires connecting for the Dark Blue and White. The spade on the motor for the red wire MUST be capped to prevent an accidental shorting of the circuit. Connecting a blank female wire terminal is the easiest way to do this.


Accentra Freestanding Instructions:

• Disconnect the stove from electrical power.

• Remove the rear access panels from the stove.

• Remove the two 5/16" screws that hold the bottom screen in place.

• Cut the wire tie that holds the power cord. Lay the assembly to the side as far as the power cord permits.

• Remove the two 1/4" bolts that hold the blower and the mounting plate.

• If the old blower is

- Bay Motor, all blower wires get cut as close to the blower as possible.

- EBM, the wire terminals will disconnect from the blower.

• Remove the old blower from the mounting plate and replace with the new blower.

• Set the blower assembly back into place.

• Strip the wires and install supplied terminals onto the wires that were cut.

• Connect the wires to the proper terminals on the blower motor.

- Light blue or white wire goes to terminal #1.

- Dark blue or black wire goes to terminal #2.

- Red wire goes to terminal #3.

- Green wire goes to the ground post.

• Tie the wires together to keep them away from any moving parts or any sharp edges.

• Install the bolts and washers that hold the blower assembly in place. Check that the ground wire and the post on the blower have clearance to the shield. If they touch, gently bend the ground post out of the way.

• Install the bottom screen onto the stove and secure it with the screws that were removed.

• Tie the power cord to the original location.

• Replace the rear access panels.

• Restore electrical power to the stove.

• Turn the feed knob to test mode. Verify the blower speed slows down when switching from high to low on the rocker switch. If it does not, reverse the top and bottom wires on the rocker switch.


XXV Instructions:

• Disconnect the stove from electrical power.

• Remove the rear access panels from the stove.

• Disconnect the wires that go to the blower.

• Loosen the two 5/16" screws located behind the ash door spring on the right side of the stove when facing the front.

• Remove the two inner 5/16" screws from the bottom of the left side of stove when facing the front.

• Lower the blower assembly, left side first. Unhook the right side and slide it out from under the stove.

• Cut the ties that hold the wires to the carrier.

• Remove the eight screws that hold the blower to the carrier and separate.

- If the old blower is a Bay Motor, all wires get cut as close to the blower as possible.

- If the old blower is an EBM, the wire terminals will disconnect from the blower.

- The green ground wire will not be used so it can be discarded.

• Strip the wires and install supplied terminals onto the wires that were cut.

• Connect the wires to the proper terminals on the blower motor.

- Light blue or white wire goes to terminal #1.

- Dark blue or black wire goes to terminal #2.

- Red wire goes to terminal #3.

• Tie all wires to terminal ends.

• When done the wires and wire tie ends cannot be under the plastic part of the motor windings due to clearance.

• Mount the blower onto the housing, keeping the wires out from between the motor coil and the blower housing.

• Run the wiring with the protective sleeve installed over the wires where they are tied to the metal housing. Be sure to route and tie the wires to keep them away from any moving parts or sharp edges.

• Slide the blower assembly back under the stove.

• Lift the right side of the blower, leaving the left side hang down.

• Slip the lip of the blower housing over the bolts that were loosened

to remove the blower.

• Lift the left side up while guiding the wires into the back of the stove and install the two mounting screws. Tighten all four mounting screws.

• Connect the wires to speed switch as follows.

- Red to the top terminal of the speed switch.

- Dark blue or black to the bottom terminal of the speed switch.

• Tie the wires together to keep them away from any moving parts and away from any sharp edges.

• Replace the rear access panels

• Restore the electrical power to the stove.

• Turn the feed knob to test mode. Verify the blower speed slows down when switching from high to low settings on the rocker switch. If it does not, reverse the top and bottom wires on the rocker switch.

Troubleshooting

This is called a tangential blower. On this blower, the motor is in the middle and there are two tangential fans. The fans are mounted over a slip grommet near the motor and are stabilized with another grommet on each end of the blower fans. The number one cause of failure with tangential blowers is a build up of hair and debris on the outer grommets. From time to time, especially if you have house pets, the outer grommets may need to be pulled out and the blower axial pins cleaned.

There are two types of outer grommets that have been used in this blower. If you have a grommet with a brass bearing inside, remove the bearing from the grommet, clean it, apply two drops of 3 in 1 oil in the grommet and reinstall with the smaller diameter bearing out. If you have a nylon (white) bearing in the grommet, remove the bearing, wash it and apply one squirt of a dry silicone spray and reinstall the bearing. Additionally, when cleaning the fins (fan blades) of this type of blower, DO NOT PUSH THE BLOWER FAN to either side. The blower fan can slip left and right to center it in the housing, the fan blades can become jammed if they are pushed too far to either side when cleaning.



Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Information

This Item Qualifies For Free Shipping!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information
Jump back to product information tab navigation

Description

Harman Convection Blower 1-00-29145. There have been many revisions to this motor over the years. This version of the blower has been in service for quite a while now and is very stable in all compatible units.

 

As technical revisions were made, this blower was also referred to as 3-21-29045, 3-21-29145, and 3-21-39145 which are now obsolete part #'s. Part 1-00-29145 is the most current revision.

When mounting this motor into the Harman Accentra-Cast, this is the pad gasket that sits under the motor, 3-44-247118


Replacement For Part Numbers:

  • 1-00-29145
  • 3-21-29045
  • 3-21-29145
  • 3-21-39145

View Compatible Models

UPC: 652174670741

Technical Specs

Wiring Connectors 2 or 3 Female
Tools Required 5/16" socket Phillips Screwdriver #2 | Accentra FS also requires 3/8" socket with extension
Volts 120V
RPM 1500 RPM
Cycles 60 HZ
Amps 1.17 AMPS
Blower Dimensions 19"W X 3-1/2"H X 4-1/4" D
Mount Holes on Center 18-1/2" W X 1" D
Mounting Plate Overall 19-1/8"W x 2-1/8" D

Instructions

Assembly Instructions For Harman Distribution Blower: 1-00-29145

XXV/ Accentra-Cast units made without a rocker switch will ONLY have wires connecting for the Dark Blue and White. The spade on the motor for the red wire MUST be capped to prevent an accidental shorting of the circuit. Connecting a blank female wire terminal is the easiest way to do this.


Accentra Freestanding Instructions:

• Disconnect the stove from electrical power.

• Remove the rear access panels from the stove.

• Remove the two 5/16" screws that hold the bottom screen in place.

• Cut the wire tie that holds the power cord. Lay the assembly to the side as far as the power cord permits.

• Remove the two 1/4" bolts that hold the blower and the mounting plate.

• If the old blower is

- Bay Motor, all blower wires get cut as close to the blower as possible.

- EBM, the wire terminals will disconnect from the blower.

• Remove the old blower from the mounting plate and replace with the new blower.

• Set the blower assembly back into place.

• Strip the wires and install supplied terminals onto the wires that were cut.

• Connect the wires to the proper terminals on the blower motor.

- Light blue or white wire goes to terminal #1.

- Dark blue or black wire goes to terminal #2.

- Red wire goes to terminal #3.

- Green wire goes to the ground post.

• Tie the wires together to keep them away from any moving parts or any sharp edges.

• Install the bolts and washers that hold the blower assembly in place. Check that the ground wire and the post on the blower have clearance to the shield. If they touch, gently bend the ground post out of the way.

• Install the bottom screen onto the stove and secure it with the screws that were removed.

• Tie the power cord to the original location.

• Replace the rear access panels.

• Restore electrical power to the stove.

• Turn the feed knob to test mode. Verify the blower speed slows down when switching from high to low on the rocker switch. If it does not, reverse the top and bottom wires on the rocker switch.


XXV Instructions:

• Disconnect the stove from electrical power.

• Remove the rear access panels from the stove.

• Disconnect the wires that go to the blower.

• Loosen the two 5/16" screws located behind the ash door spring on the right side of the stove when facing the front.

• Remove the two inner 5/16" screws from the bottom of the left side of stove when facing the front.

• Lower the blower assembly, left side first. Unhook the right side and slide it out from under the stove.

• Cut the ties that hold the wires to the carrier.

• Remove the eight screws that hold the blower to the carrier and separate.

- If the old blower is a Bay Motor, all wires get cut as close to the blower as possible.

- If the old blower is an EBM, the wire terminals will disconnect from the blower.

- The green ground wire will not be used so it can be discarded.

• Strip the wires and install supplied terminals onto the wires that were cut.

• Connect the wires to the proper terminals on the blower motor.

- Light blue or white wire goes to terminal #1.

- Dark blue or black wire goes to terminal #2.

- Red wire goes to terminal #3.

• Tie all wires to terminal ends.

• When done the wires and wire tie ends cannot be under the plastic part of the motor windings due to clearance.

• Mount the blower onto the housing, keeping the wires out from between the motor coil and the blower housing.

• Run the wiring with the protective sleeve installed over the wires where they are tied to the metal housing. Be sure to route and tie the wires to keep them away from any moving parts or sharp edges.

• Slide the blower assembly back under the stove.

• Lift the right side of the blower, leaving the left side hang down.

• Slip the lip of the blower housing over the bolts that were loosened

to remove the blower.

• Lift the left side up while guiding the wires into the back of the stove and install the two mounting screws. Tighten all four mounting screws.

• Connect the wires to speed switch as follows.

- Red to the top terminal of the speed switch.

- Dark blue or black to the bottom terminal of the speed switch.

• Tie the wires together to keep them away from any moving parts and away from any sharp edges.

• Replace the rear access panels

• Restore the electrical power to the stove.

• Turn the feed knob to test mode. Verify the blower speed slows down when switching from high to low settings on the rocker switch. If it does not, reverse the top and bottom wires on the rocker switch.

Troubleshooting

This is called a tangential blower. On this blower, the motor is in the middle and there are two tangential fans. The fans are mounted over a slip grommet near the motor and are stabilized with another grommet on each end of the blower fans. The number one cause of failure with tangential blowers is a build up of hair and debris on the outer grommets. From time to time, especially if you have house pets, the outer grommets may need to be pulled out and the blower axial pins cleaned.

There are two types of outer grommets that have been used in this blower. If you have a grommet with a brass bearing inside, remove the bearing from the grommet, clean it, apply two drops of 3 in 1 oil in the grommet and reinstall with the smaller diameter bearing out. If you have a nylon (white) bearing in the grommet, remove the bearing, wash it and apply one squirt of a dry silicone spray and reinstall the bearing. Additionally, when cleaning the fins (fan blades) of this type of blower, DO NOT PUSH THE BLOWER FAN to either side. The blower fan can slip left and right to center it in the housing, the fan blades can become jammed if they are pushed too far to either side when cleaning.



Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information

Customer Reviews

Based on 10 reviews
100%
(10)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
R
Richard K.
Exactly as ordered.

This was my second order from Stove and Grill Parts for Less. Ordered an OEM distribution blower for my Harmon XXV pellet stove. The part was delivered as expected, at a fair price and exactly what I ordered. The OEM part needed no wiring modification and installed quickly. Great experience.

S
Steven B.
Great service

I ordered a replacement distribution blower for my Harmon Accentra pellet stove and had it in two days.

J
JOHN F.

I originally bought an aftermarket distribution blower . Had issues with it returned it ordered in OEM distribution blower . Gabe helped me through the whole process did a great job he represents his company well. I highly recommendThis company they stand behind their products in their customers

R
Robert G.P.B.2.
it`s always something!

Shipped fast,replaced blower and works well.Am happy.

P
Pat D.
Distribution Blower Harmon Accentra

Shipping was prompt 3 days. The part fit perfectly and the stove was up and running an hour after getting it. It has worked perfectly. It seemed to be equal quality as the original hopefully it lasts as long.

QUESTIONS & ANSWERS

If your question does not concern this specific product, use our contact form

Have a Question?

Be the first to ask a question about this.

Ask a Question

Customer Reviews

Based on 10 reviews
100%
(10)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
R
Richard K.
Exactly as ordered.

This was my second order from Stove and Grill Parts for Less. Ordered an OEM distribution blower for my Harmon XXV pellet stove. The part was delivered as expected, at a fair price and exactly what I ordered. The OEM part needed no wiring modification and installed quickly. Great experience.

S
Steven B.
Great service

I ordered a replacement distribution blower for my Harmon Accentra pellet stove and had it in two days.

J
JOHN F.

I originally bought an aftermarket distribution blower . Had issues with it returned it ordered in OEM distribution blower . Gabe helped me through the whole process did a great job he represents his company well. I highly recommendThis company they stand behind their products in their customers

R
Robert G.P.B.2.
it`s always something!

Shipped fast,replaced blower and works well.Am happy.

P
Pat D.
Distribution Blower Harmon Accentra

Shipping was prompt 3 days. The part fit perfectly and the stove was up and running an hour after getting it. It has worked perfectly. It seemed to be equal quality as the original hopefully it lasts as long.