Harman Pellet Insert Updated Burn Pot Retrofit Kit for the 52i Insert (1-00-574605). Problems with early Accentra52i burn pot caused an overfiring condition that warped the flame guide, medallion and may burn a hotspot (gray etching) into the center of the door glass.
The burn pot gasket and igniter cradle are included with this kit. It is important to REPLACE ALL OF THESE PARTS TOGETHER to avoid compatibility issues.
Harman Technical Updates to this Burnpot
There are three specific periods of manufacture for the Accentra 52i. Depending on when the unit was built, certain recommendations apply. Click on "Troubleshooting" above for more information.
Install Instructions For Harman 52i Updated Burn Pot Retrofit Kit: 1-00-574605
To replace the burnpot:
Unplug your stove
The igniter is inside if the burnpot. From the rear of the stove, find the yellow and light blue colored wires that are coiled up and secured to the wiring harness. cut the zip ties that hold this collection of wire together. when the burn pot is removed, this is the length of wire that will pass through the stove body as the burn pot is pulled out. If the wires are not free to travel, the burnpot will only move about 4 inches.
Locate and remove the 4 1/2" nuts that secure the burnpot to the feeder weldment threaded rods. You may need a universal joint at the end of your socket wrench to make the connection at the top nuts.
Pull the burnpot assembly forward until the yellow and light blue wires are visible, then disconnect the igniter wires. Now the burn pot is free to come out of the stove
Remove the two 5/16" screws that hold the igniter in to the burnpot and then remove the igniter assembly
If you are replacing your igniter, do this now while the burnpot is free from the stove.
Make sure to run the wires for the igniter through the right-side opening at the rear of the burn pot
Replace your burnpot gasket, make sure your yellow and light blue wires are passing through the hole and through the center of the gasket.
Connect your igniter wires and pull the yellow and light blue wires from the back of the stove so that the disconnects pass backward through the opening. Try to take out as much slack in the igniter wires as possible so that they aren't pinch by the burnpot when it is fit into place. Note: for this part of the job, having another person around to pull the wires as you fit the burnpot in stove is key.
Replace your new burn pot over the threaded rods and tighten down all 4 1/2" hex nuts. You will feel the new gasket compress as you tighten the burnpot down, this is normal. DO NOT PINCH THE IGNITER WIRES WHEN DOING THIS PART
Replace the clean out cover and secure your wires in the rear of the stove.
Troubleshooting
-Problems with early Accentra52i burn pot designs include an overfiring condition that warps the flame guide and medallion. It may also burn a hotspot (gray etching) into the center of the door glass.
Based on the changes that have been made, there are three specific periods of manufacture for the Accentra 52i. Depending on when the unit was built, the following recommendations apply:
Units built from the Launch of the Accentra52i [S/N 008254751] → 11/26/13 [S/N 008257173]: We recommend the combustion cover on all of these units is replaced with part, 1-10-574087A to prevent any issues with incorrect placement. We suggest that all combustion covers are proactively replaced on units manufactured in this time period to prevent any future issues. Additionally, if any ignition issues persist, we recommend replacing the burnpot with the new style P/N 1-00-574400 (part now obsolete, new part #,1-00-574605)
Units built from 11/26/13 [S/N 008257173] → 1/7/14 [S/N 008257557]: The likelihood of these units igniting properly is high, but in the unlikely circumstance that a unit manufactured in this period has long ignition issues, we recommend replacement of the burnpot with the new style burnpot, P/N 1-00-574400.(part now obsolete, replace with this part, 1-00-574605).
Units built from 1/7/14 [S/N 008257557] → 7/1/17: There should not be any issues with units built in this time period. - End of Accentra52i Production.
Accentra52i-TC Introduced 7/1/17 → Current: This model underwent a full redesign to incorporate the "Easy-Touch" control system which included a burnpot revision of part 1-00-574400(obsolete), the new part number introduced, 1-00-574605. This burn pot is reverse-compatible with all prior versions of the 52i as a retrofit kit. It features an improved air-flow design to work with the newer-style combustion motors and still comply with 2020 EPA certifications. The igniter cradle, #3 in Fig.1, part 1-00-777907 is now adjustable within the burnpot so the ignition can always seat flush, compensating for any variances that may have occurred in manufacturing or over firing during use. Both could lead to long or faulty ignitions.
Warranty
Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers
make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please
be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.
Shipping Information
This Item Qualifies For Free Shipping!
When Will My Order Ship?
All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.
Do You Offer Express Shipping?
Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.
How Does Free Shipping Work?
Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.
Do You Ship To Canada?
We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.
Do You Ship To Alaska Or Hawaii?
We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.
Do You Ship Outside The US Or Canada?
Unfortunately, at this time we do not offer international shipping other than to Canada.
Shipping Time Estimations
For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.
Harman Pellet Insert Updated Burn Pot Retrofit Kit for the 52i Insert (1-00-574605). Problems with early Accentra52i burn pot caused an overfiring condition that warped the flame guide, medallion and may burn a hotspot (gray etching) into the center of the door glass.
The burn pot gasket and igniter cradle are included with this kit. It is important to REPLACE ALL OF THESE PARTS TOGETHER to avoid compatibility issues.
Harman Technical Updates to this Burnpot
There are three specific periods of manufacture for the Accentra 52i. Depending on when the unit was built, certain recommendations apply. Click on "Troubleshooting" above for more information.
Install Instructions For Harman 52i Updated Burn Pot Retrofit Kit: 1-00-574605
To replace the burnpot:
Unplug your stove
The igniter is inside if the burnpot. From the rear of the stove, find the yellow and light blue colored wires that are coiled up and secured to the wiring harness. cut the zip ties that hold this collection of wire together. when the burn pot is removed, this is the length of wire that will pass through the stove body as the burn pot is pulled out. If the wires are not free to travel, the burnpot will only move about 4 inches.
Locate and remove the 4 1/2" nuts that secure the burnpot to the feeder weldment threaded rods. You may need a universal joint at the end of your socket wrench to make the connection at the top nuts.
Pull the burnpot assembly forward until the yellow and light blue wires are visible, then disconnect the igniter wires. Now the burn pot is free to come out of the stove
Remove the two 5/16" screws that hold the igniter in to the burnpot and then remove the igniter assembly
If you are replacing your igniter, do this now while the burnpot is free from the stove.
Make sure to run the wires for the igniter through the right-side opening at the rear of the burn pot
Replace your burnpot gasket, make sure your yellow and light blue wires are passing through the hole and through the center of the gasket.
Connect your igniter wires and pull the yellow and light blue wires from the back of the stove so that the disconnects pass backward through the opening. Try to take out as much slack in the igniter wires as possible so that they aren't pinch by the burnpot when it is fit into place. Note: for this part of the job, having another person around to pull the wires as you fit the burnpot in stove is key.
Replace your new burn pot over the threaded rods and tighten down all 4 1/2" hex nuts. You will feel the new gasket compress as you tighten the burnpot down, this is normal. DO NOT PINCH THE IGNITER WIRES WHEN DOING THIS PART
Replace the clean out cover and secure your wires in the rear of the stove.
Troubleshooting
-Problems with early Accentra52i burn pot designs include an overfiring condition that warps the flame guide and medallion. It may also burn a hotspot (gray etching) into the center of the door glass.
Based on the changes that have been made, there are three specific periods of manufacture for the Accentra 52i. Depending on when the unit was built, the following recommendations apply:
Units built from the Launch of the Accentra52i [S/N 008254751] → 11/26/13 [S/N 008257173]: We recommend the combustion cover on all of these units is replaced with part, 1-10-574087A to prevent any issues with incorrect placement. We suggest that all combustion covers are proactively replaced on units manufactured in this time period to prevent any future issues. Additionally, if any ignition issues persist, we recommend replacing the burnpot with the new style P/N 1-00-574400 (part now obsolete, new part #,1-00-574605)
Units built from 11/26/13 [S/N 008257173] → 1/7/14 [S/N 008257557]: The likelihood of these units igniting properly is high, but in the unlikely circumstance that a unit manufactured in this period has long ignition issues, we recommend replacement of the burnpot with the new style burnpot, P/N 1-00-574400.(part now obsolete, replace with this part, 1-00-574605).
Units built from 1/7/14 [S/N 008257557] → 7/1/17: There should not be any issues with units built in this time period. - End of Accentra52i Production.
Accentra52i-TC Introduced 7/1/17 → Current: This model underwent a full redesign to incorporate the "Easy-Touch" control system which included a burnpot revision of part 1-00-574400(obsolete), the new part number introduced, 1-00-574605. This burn pot is reverse-compatible with all prior versions of the 52i as a retrofit kit. It features an improved air-flow design to work with the newer-style combustion motors and still comply with 2020 EPA certifications. The igniter cradle, #3 in Fig.1, part 1-00-777907 is now adjustable within the burnpot so the ignition can always seat flush, compensating for any variances that may have occurred in manufacturing or over firing during use. Both could lead to long or faulty ignitions.
Warranty
Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers
make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please
be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.
Shipping Info
This Item Qualifies For Free Shipping!
When Will My Order Ship?
All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.
Do You Offer Express Shipping?
Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.
How Does Free Shipping Work?
Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.
Do You Ship To Canada?
We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.
Do You Ship To Alaska Or Hawaii?
We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.
Do You Ship Outside The US Or Canada?
Unfortunately, at this time we do not offer international shipping other than to Canada.
Shipping Time Estimations
For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.
Our burn pot cracked and I ordered it from you. Had it in two days and had trouble putting it in but with your help it worked great. Best place I have delt with.
S
SD H.
Harman Burnpot
Great price and fast shipping on this OEM component!
A
Anonymous
Burn Pot Order
My experience was excellent
QUESTIONS & ANSWERS
If your question does not concern this specific product, use our contact form
Our burn pot cracked and I ordered it from you. Had it in two days and had trouble putting it in but with your help it worked great. Best place I have delt with.
S
SD H.
Harman Burnpot
Great price and fast shipping on this OEM component!
