Harman Pellet Stove OEM Burn Pot Weldment 1-10-00675. The Burn Pot is an integral part of your pellet stove's feed system. It is important to periodically inspect the pot to make sure it is not damaged. If you notice any holes, warpage or cracks forming in the pot, it should be replaced!
Note: *Anytime the burn pot is removed or replaced a new gasket should be installed (Burn Pot gasket sold separately).*
NOTE - Accentra Insert was discontinued in 2012 and became the Accentra 52i, and later the Accentra52i-TC, which all use burnpot 1-00-574605
Inside of the burnpot weldment assembly there is an igniter and mounting bracket called a cradle. Because these parts need to be removed when changing the burnpot it's recommended to replace them to get the best performance from the new burnpot weldment. Additionally, there has been a redesign of the cradle. Old cradles in new burnpots may delay ignition times causing the stove to error.
Install Instructions For Harman Burn Pot Weldment: 1-10-00675
1.)Unplug your stove and make sure that the unit is cool to the touch.
2.)Remove the side and rear panels from the unit and locate the yellow and light blue colored wiresthat are coiled up.
3.)Cut the zip ties that hold this collection of wire together (When the burn pot is removed, this extra wire (yellow and blue) needs to be fed back into the neck of the burn pot. The igniter is located inside if the burnpot. This step must be taken so you can disconnect the ignitor when replacing the pot).
4.) Locate and remove the (4) 1/2" nuts that secure the burnpot to the threaded rods coming from the feeder weldment (You may need a universal joint at the end of your socket wrench to make the connection at the top nuts).
5.) Pull the burnpot assembly forward until the yellow and light blue wires are visible, then disconnect the igniter wires.
6.) Now the burn pot is free and can be removed from the stove.
7.) Remove the two 5/16" screws that attach the igniter cradle in to the burnpot and remove the igniter assembly.
(This is a good time to replace the ignitor if you need to do so).
8.) Replace your burnpot gasket. (Make sure the yellow and light blue wires coming from the rear of the unit are passing through the burn pot gasket and are not pinched between the gasket and the rear of the stove).
9.) Connect your igniter wires and pull the yellow and light blue wires from the back of the stove so that the disconnects pass backward through the opening(Try to take out as much slack in the igniter wires as possible so that they aren't pinch by the burnpot when it is fit into place. Also, make sure to run the wires for the igniter through the right-side opening at the bottom rear of the burn pot).
10.) Place your new burn pot over the threaded rods and tighten down all (4) 1/2" hex nuts by hand. Once all nuts are tightened by hand finish tightening in a crisscross pattern using your wrench or socket. This will ensure that the burn pot and gasket seats evenly against the back of the unit).
11.) Replace the clean out cover.
12.) Secure the wires you previously freed up at the rear of the stove using a zip tie and reinstall any panels that were removed.
Troubleshooting
-The burn pot is an integral part of the Harman feed system and will often last the life of the stove.
-It is important to inspect your burn pot on a regular basis. If you notice any holes, warping or cracks formingthe pot should be replaced.
Before replacing the burn pot to correct delayed ignitions, try each of the following:
If you have excessive amounts of carbon build up around the base of the burn pot, tighten the (4) 1/2" nuts that secure the burn-pot in place, this may help. If It Does not resolve the issue you may want to consider replacing the burn pot gasket.
Replace your door and ash pan gasket (If you have separate doors).
Look at your door handle and inspect the latch mechanism to make sure the door is latching properly.
Make sure the hopper lid is making a tight seal.
Warranty
Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers
make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please
be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.
Shipping Information
This Item Qualifies For Free Shipping!
HOLIDAY UPDATE
Due to the upcoming Christmas and New Years holidays, shippers will not be picking up on the dates below. Additionally, packages may take longer to arrive than expected. We appreciate your understanding and patience during this time.
USPS:
No pickup on Dec 24th, Dec 25th, and Jan 1st.
UPS:
No pickup on Dec 24th (except NDA and 2nd Day), Dec 25th, Dec 31st (except NDA and 2nd Day), and Jan 1st.
CANADA UPDATE
Due to the ongoing Canada Post postal workers' strike, we are forced to suspend all ordering to Canada. Please be advised that any shipments that did not clear U.S. customs by November 15th will be delayed until Canada Post is fully operational. We appreciate your understanding and patience during this time.
When Will My Order Ship?
All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.
Do You Offer Express Shipping?
Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.
How Does Free Shipping Work?
Most orders over $49 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.
Do You Ship To Canada?
We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.
Do You Ship To Alaska Or Hawaii?
We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.
Do You Ship Outside The US Or Canada?
Unfortunately, at this time we do not offer international shipping other than to Canada.
Shipping Time Estimations
For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.
Harman Pellet Stove OEM Burn Pot Weldment 1-10-00675. The Burn Pot is an integral part of your pellet stove's feed system. It is important to periodically inspect the pot to make sure it is not damaged. If you notice any holes, warpage or cracks forming in the pot, it should be replaced!
Note: *Anytime the burn pot is removed or replaced a new gasket should be installed (Burn Pot gasket sold separately).*
NOTE - Accentra Insert was discontinued in 2012 and became the Accentra 52i, and later the Accentra52i-TC, which all use burnpot 1-00-574605
Inside of the burnpot weldment assembly there is an igniter and mounting bracket called a cradle. Because these parts need to be removed when changing the burnpot it's recommended to replace them to get the best performance from the new burnpot weldment. Additionally, there has been a redesign of the cradle. Old cradles in new burnpots may delay ignition times causing the stove to error.
Install Instructions For Harman Burn Pot Weldment: 1-10-00675
1.)Unplug your stove and make sure that the unit is cool to the touch.
2.)Remove the side and rear panels from the unit and locate the yellow and light blue colored wiresthat are coiled up.
3.)Cut the zip ties that hold this collection of wire together (When the burn pot is removed, this extra wire (yellow and blue) needs to be fed back into the neck of the burn pot. The igniter is located inside if the burnpot. This step must be taken so you can disconnect the ignitor when replacing the pot).
4.) Locate and remove the (4) 1/2" nuts that secure the burnpot to the threaded rods coming from the feeder weldment (You may need a universal joint at the end of your socket wrench to make the connection at the top nuts).
5.) Pull the burnpot assembly forward until the yellow and light blue wires are visible, then disconnect the igniter wires.
6.) Now the burn pot is free and can be removed from the stove.
7.) Remove the two 5/16" screws that attach the igniter cradle in to the burnpot and remove the igniter assembly.
(This is a good time to replace the ignitor if you need to do so).
8.) Replace your burnpot gasket. (Make sure the yellow and light blue wires coming from the rear of the unit are passing through the burn pot gasket and are not pinched between the gasket and the rear of the stove).
9.) Connect your igniter wires and pull the yellow and light blue wires from the back of the stove so that the disconnects pass backward through the opening(Try to take out as much slack in the igniter wires as possible so that they aren't pinch by the burnpot when it is fit into place. Also, make sure to run the wires for the igniter through the right-side opening at the bottom rear of the burn pot).
10.) Place your new burn pot over the threaded rods and tighten down all (4) 1/2" hex nuts by hand. Once all nuts are tightened by hand finish tightening in a crisscross pattern using your wrench or socket. This will ensure that the burn pot and gasket seats evenly against the back of the unit).
11.) Replace the clean out cover.
12.) Secure the wires you previously freed up at the rear of the stove using a zip tie and reinstall any panels that were removed.
Troubleshooting
-The burn pot is an integral part of the Harman feed system and will often last the life of the stove.
-It is important to inspect your burn pot on a regular basis. If you notice any holes, warping or cracks formingthe pot should be replaced.
Before replacing the burn pot to correct delayed ignitions, try each of the following:
If you have excessive amounts of carbon build up around the base of the burn pot, tighten the (4) 1/2" nuts that secure the burn-pot in place, this may help. If It Does not resolve the issue you may want to consider replacing the burn pot gasket.
Replace your door and ash pan gasket (If you have separate doors).
Look at your door handle and inspect the latch mechanism to make sure the door is latching properly.
Make sure the hopper lid is making a tight seal.
Warranty
Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers
make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please
be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.
Shipping Info
This Item Qualifies For Free Shipping!
HOLIDAY UPDATE
Due to the upcoming Christmas and New Years holidays, shippers will not be picking up on the dates below. Additionally, packages may take longer to arrive than expected. We appreciate your understanding and patience during this time.
USPS:
No pickup on Dec 24th, Dec 25th, and Jan 1st.
UPS:
No pickup on Dec 24th (except NDA and 2nd Day), Dec 25th, Dec 31st (except NDA and 2nd Day), and Jan 1st.
CANADA UPDATE
Due to the ongoing Canada Post postal workers' strike, we are forced to suspend all ordering to Canada. Please be advised that any shipments that did not clear U.S. customs by November 15th will be delayed until Canada Post is fully operational. We appreciate your understanding and patience during this time.
When Will My Order Ship?
All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.
Do You Offer Express Shipping?
Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.
How Does Free Shipping Work?
Most orders over $49 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.
Do You Ship To Canada?
We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.
Do You Ship To Alaska Or Hawaii?
We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.
Do You Ship Outside The US Or Canada?
Unfortunately, at this time we do not offer international shipping other than to Canada.
Shipping Time Estimations
For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.
All my concerns regarding my purchase were readily answered and the delivery to the west coast of British Columbia very fast and on time. A definite go to store for any purchases
G
Gary C.
Harmon burn pot
The parts were easy to order ,got to me faster than expected and were easy to install, it all fit perfect
QUESTIONS & ANSWERS
If your question does not concern this specific product, use our contact form
If you have a Harman Accenra Insert then, yes, you need to use the flame guide - part number 3-00-03000. If you have the freestanding version then you will need to use this flame guide - part number 3-00-08534. The function of the flame guide is to distribute the heat evenly over the heat exchanger.
All my concerns regarding my purchase were readily answered and the delivery to the west coast of British Columbia very fast and on time. A definite go to store for any purchases
G
Gary C.
Harmon burn pot
The parts were easy to order ,got to me faster than expected and were easy to install, it all fit perfect
