Skip to main content
Skip to main content
Product title:

Harman Adjustable Igniter Cradle (Updated): 1-00-777907

Product rating:
Product price:
$89.99
Product SKU ! 1-00-777907
Product MPN ! 1-00-777907
Product availability: In Stock
Bullet point features

Frequently Bought Together

Description

Harman Adjustable Igniter Cradle (Updated).  This cradle can be used on any units using finned igniters and is backward-compatible with all auto-ignition models that previously used part # 1-00-067620, which is being phased out by Harman.

The screws that are included should be installed into the lower holes on the cradle.  When tightened, these screws will gently push the ignitor against the bottom of the burn pot.

This cradle is sold without mounting hardware and your existing screws must be reused. New screws can be purchased using Harman part# 3-30-1101-100, QTY 2.

Important: Do not overtighten the screws that press the adjustable plate against the bottom of the igniter.  Overtightening these screws can cause the cradle to push away from the bottom of the burn pot, causing ignition issues.

Notes:

  • Accentra52i / Accentra52i-TC ONLY use this cradle when using burn pot 1-00-574605
  • Absolute43 uses cradle part # 1-00-777906

 

The diagram below shows where this part is used, Fig.1.3

Fig.1.2 - 3-20-677200 Igniter

Fig.1.4/ 1.5 - 1-00-06623 Burnpot Cover with Wingscrews

Notes:

  • Accentra52i and Accentra52i-TC ONLY use this cradle when using burnpot 1-00-574605
  • Absolute43 uses cradle part # 1-00-777906


Replacement For Part Numbers:

  • 1-00-777907
  • 1-00-06620
  • 1-00-574604

View Compatible Models

UPC: 652174924509

Compatible Models

    Harman

  • Absolute 63 (Post: HF1533400)
  • Accentra 52i (008259179 - 008259179)
  • Accentra 52i TC
  • Accentra Cast FS
  • Accentra Insert
  • Advance
  • Allure 50
  • Allure 50-CE
  • P35i
  • P35i-C
  • P43
  • P43-C
  • P61-A
  • P61-C
  • P61A
  • P68
  • P68-C
  • PB105 (Pre: 008341122)
  • PF100 (Pre: 004351831)
  • XXV (Pre: May 2013)
  • XXV TC

Technical Specs

Videos

Instructions

Install Instructions For Harman Adjustable Igniter Cradle (Updated): 1-00-777907

Igniter Cradle/Holder Installation Instructions:


1.) The igniter cradle/holder is located in the burn pot. (To access the cradle you must loosen the two wing nuts securing the burn pot clean-out cover to the bottom of the pot. Once both wing nuts are loosened the cover plate can be removed).

2.) From the front of the stove, remove the two 5/16" or 8mm screws that hold the igniter cradle inside the burn pot. This will allow the cradle to drop out (Do not discard these screws).

3.) To remove the igniter from the old-style cradle/holder, twist the two tabs that secure the flat plate to the ignitor. Your old igniter can now be removed (Pay special attention to how the ignitor is positioned in the cradle).

4.) Position your ignitor into the new cradle (If you are replacing the igniter at this time follow the instructions below on igniter replacement).

5.) Position the new cradle/holder in the same orientation as the previous holder and install the cradle using the two 5/16" or 8mm mounting screws (Updated cradles do not have a retainer plate).

6.) The new cradle/holder will have 2 holes for additional screws under the ignitor. Gently tighten these screws. This will push the igniter against the bottom of the burn pot (Do not over-tighten these screws).





Igniter Installation Instructions:


1.) The igniter is located in the burn pot. (To access the ignitor you must first loosen the two wing nuts securing the burn pot clean-out cover to the bottom of the pot. Once both wing nuts are loosened the cover plate can be removed).


2.) The igniter is accessed and changed through the front of the stove, but you will also need to access the rear of the stove to free the wiring.


3.) From the rear of the unit, locate the yellow and light blue wires for the igniter at the point where they pass through the neck of the burn pot into the rear of the stove, it is directly under the auger (On freestanding stoves this will require that the rear / side shields are removed. When replacing the ignitor on an insert the unit will need to be slid forward and pulled out of the firebox. On some units, there may be a small rubber grommet or a dab of high temp silicone where the ignitor wires transition to the back of the unit.)


4.) In this area you should notice extra wire looped together (Likely, this excess wire will be secured in position with a zip tie). This extra wire needs to be freed up so that the disconnects can be pulled forward and disconnected from the neck of the burn pot. This can be done by carefully cutting the zip tie and gently pushing about 12" of the yellow and light blue wire into the cavity of the stove where the ignitor is located.


5.) From the front of the stove, remove the two 5/16" or 8mm screws that hold the igniter cradle inside the burn pot (Do not discard these screws).

 

 6.) Drop the igniter assembly down and pull it forward until you can see the wire disconnects, then disconnect the wires from the harness and remove the whole assembly.

 

7.) To remove the igniter from the (old style) cradle, twist the two tabs that secure the flat plate to the ignitor. Your old igniter can now be removed (Pay special attention to how the ignitor is positioned in the cradle. The replacement will be positioned in the same way).


8.) Position your new ignitor in the cradle and reinstall the cradle using the two 5/16" or 8mm mounting screws (The updated cradle does not have a retainer plate).

 

9.) From the rear of the unit, gently pull the excess wire you previously feed forward to remove the slack, coil the extra wire length, and secure it with a zip tie.


10.) Reinstall the cover plate and test your ignitor to ensure it is operating correctly.

Troubleshooting

If you are experiencing delayed ignitions and can verify that the igniter is getting hot:


  1. Tighten the four 1/2" nuts that secure the burn pot.
  2. Replace the door gasket and ash pan gasket (if you have separate doors).
  3. Look at your door handle to make sure the components of the handle and the catch on the stove are in working order.
  4. Make sure the hopper lid is making a tight seal.


If you have done all of these things and the stove still isn't firing up, replacing the cradle may solve the problem.


It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Information

This Item Qualifies For Free Shipping With Orders Over $199!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information
Jump back to product information tab navigation

Description

Harman Adjustable Igniter Cradle (Updated).  This cradle can be used on any units using finned igniters and is backward-compatible with all auto-ignition models that previously used part # 1-00-067620, which is being phased out by Harman.

The screws that are included should be installed into the lower holes on the cradle.  When tightened, these screws will gently push the ignitor against the bottom of the burn pot.

This cradle is sold without mounting hardware and your existing screws must be reused. New screws can be purchased using Harman part# 3-30-1101-100, QTY 2.

Important: Do not overtighten the screws that press the adjustable plate against the bottom of the igniter.  Overtightening these screws can cause the cradle to push away from the bottom of the burn pot, causing ignition issues.

Notes:

  • Accentra52i / Accentra52i-TC ONLY use this cradle when using burn pot 1-00-574605
  • Absolute43 uses cradle part # 1-00-777906

 

The diagram below shows where this part is used, Fig.1.3

Fig.1.2 - 3-20-677200 Igniter

Fig.1.4/ 1.5 - 1-00-06623 Burnpot Cover with Wingscrews

Notes:

  • Accentra52i and Accentra52i-TC ONLY use this cradle when using burnpot 1-00-574605
  • Absolute43 uses cradle part # 1-00-777906


Replacement For Part Numbers:

  • 1-00-777907
  • 1-00-06620
  • 1-00-574604

View Compatible Models

UPC: 652174924509

Compatible Models

    Harman

  • Absolute 63 (Post: HF1533400)
  • Accentra 52i (008259179 - 008259179)
  • Accentra 52i TC
  • Accentra Cast FS
  • Accentra Insert
  • Advance
  • Allure 50
  • Allure 50-CE
  • P35i
  • P35i-C
  • P43
  • P43-C
  • P61-A
  • P61-C
  • P61A
  • P68
  • P68-C
  • PB105 (Pre: 008341122)
  • PF100 (Pre: 004351831)
  • XXV (Pre: May 2013)
  • XXV TC

Instructions

Assembly Instructions For Harman Adjustable Igniter Cradle (Updated): 1-00-777907

Igniter Cradle/Holder Installation Instructions:


1.) The igniter cradle/holder is located in the burn pot. (To access the cradle you must loosen the two wing nuts securing the burn pot clean-out cover to the bottom of the pot. Once both wing nuts are loosened the cover plate can be removed).

2.) From the front of the stove, remove the two 5/16" or 8mm screws that hold the igniter cradle inside the burn pot. This will allow the cradle to drop out (Do not discard these screws).

3.) To remove the igniter from the old-style cradle/holder, twist the two tabs that secure the flat plate to the ignitor. Your old igniter can now be removed (Pay special attention to how the ignitor is positioned in the cradle).

4.) Position your ignitor into the new cradle (If you are replacing the igniter at this time follow the instructions below on igniter replacement).

5.) Position the new cradle/holder in the same orientation as the previous holder and install the cradle using the two 5/16" or 8mm mounting screws (Updated cradles do not have a retainer plate).

6.) The new cradle/holder will have 2 holes for additional screws under the ignitor. Gently tighten these screws. This will push the igniter against the bottom of the burn pot (Do not over-tighten these screws).





Igniter Installation Instructions:


1.) The igniter is located in the burn pot. (To access the ignitor you must first loosen the two wing nuts securing the burn pot clean-out cover to the bottom of the pot. Once both wing nuts are loosened the cover plate can be removed).


2.) The igniter is accessed and changed through the front of the stove, but you will also need to access the rear of the stove to free the wiring.


3.) From the rear of the unit, locate the yellow and light blue wires for the igniter at the point where they pass through the neck of the burn pot into the rear of the stove, it is directly under the auger (On freestanding stoves this will require that the rear / side shields are removed. When replacing the ignitor on an insert the unit will need to be slid forward and pulled out of the firebox. On some units, there may be a small rubber grommet or a dab of high temp silicone where the ignitor wires transition to the back of the unit.)


4.) In this area you should notice extra wire looped together (Likely, this excess wire will be secured in position with a zip tie). This extra wire needs to be freed up so that the disconnects can be pulled forward and disconnected from the neck of the burn pot. This can be done by carefully cutting the zip tie and gently pushing about 12" of the yellow and light blue wire into the cavity of the stove where the ignitor is located.


5.) From the front of the stove, remove the two 5/16" or 8mm screws that hold the igniter cradle inside the burn pot (Do not discard these screws).

 

 6.) Drop the igniter assembly down and pull it forward until you can see the wire disconnects, then disconnect the wires from the harness and remove the whole assembly.

 

7.) To remove the igniter from the (old style) cradle, twist the two tabs that secure the flat plate to the ignitor. Your old igniter can now be removed (Pay special attention to how the ignitor is positioned in the cradle. The replacement will be positioned in the same way).


8.) Position your new ignitor in the cradle and reinstall the cradle using the two 5/16" or 8mm mounting screws (The updated cradle does not have a retainer plate).

 

9.) From the rear of the unit, gently pull the excess wire you previously feed forward to remove the slack, coil the extra wire length, and secure it with a zip tie.


10.) Reinstall the cover plate and test your ignitor to ensure it is operating correctly.

Troubleshooting

If you are experiencing delayed ignitions and can verify that the igniter is getting hot:


  1. Tighten the four 1/2" nuts that secure the burn pot.
  2. Replace the door gasket and ash pan gasket (if you have separate doors).
  3. Look at your door handle to make sure the components of the handle and the catch on the stove are in working order.
  4. Make sure the hopper lid is making a tight seal.


If you have done all of these things and the stove still isn't firing up, replacing the cradle may solve the problem.


It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping With Orders Over $199!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $199 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information

Customer Reviews

Based on 3 reviews
100%
(3)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
J
Jeffrey W.
Great part

Part fit perfectly. Updated design but still installed easily!

M
Mark M.
Conversion parts

I ordered several parts to convert a Harman P38, into a P43 auto ignition. The order arrived quickly and packed securely. I would definitely order from here again. Prices are reasonable as well. Mark M.

K
Ken S.
Great products

Parts were a direct fit and solved my problem. I really appreciate the fast service.

QUESTIONS & ANSWERS

If your question does not concern this specific product, use our contact form

Have a Question?

Be the first to ask a question about this.

Ask a Question

Customer Reviews

Based on 3 reviews
100%
(3)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
J
Jeffrey W.
Great part

Part fit perfectly. Updated design but still installed easily!

M
Mark M.
Conversion parts

I ordered several parts to convert a Harman P38, into a P43 auto ignition. The order arrived quickly and packed securely. I would definitely order from here again. Prices are reasonable as well. Mark M.

K
Ken S.
Great products

Parts were a direct fit and solved my problem. I really appreciate the fast service.